Help needed no s3 in xbmcbuntu but BIOS is set for s3 - Printable Version +- Kodi Community Forum (https://forum.kodi.tv) +-- Forum: Support (https://forum.kodi.tv/forumdisplay.php?fid=33) +--- Forum: General Support (https://forum.kodi.tv/forumdisplay.php?fid=111) +---- Forum: Linux (https://forum.kodi.tv/forumdisplay.php?fid=52) +---- Thread: Help needed no s3 in xbmcbuntu but BIOS is set for s3 (/showthread.php?tid=133058) |
Help needed no s3 in xbmcbuntu but BIOS is set for s3 - richarddc79 - 2012-06-03 Hi, hopefully someone can help, I have an Asus M4a88 motherboard and have set the BIOS to S3 and installed XBMCBUNTU, however when i add the command echo USB4 > /proc/acpi/wakeup this is what i see root@xbmc1:~# cat /proc/acpi/wakeup Device S-state Status Sysfs node PCE2 S4 *disabled pci:0000:00:02.0 PCE3 S4 *disabled PCE6 S4 *disabled PCE7 S4 *disabled PCE9 S4 *disabled PCEA S4 *disabled pci:0000:00:0a.0 RLAN S4 *enabled pci:0000:02:00.0 SBAZ S4 *disabled pci:0000:00:14.2 UAR1 S4 *disabled pnp:00:08 P0PC S4 *disabled pci:0000:00:14.4 UHC1 S4 *disabled pci:0000:00:12.0 UHC2 S4 *disabled pci:0000:00:12.1 UHC3 S4 *disabled pci:0000:00:12.2 USB4 S4 *enabled pci:0000:00:13.0 UHC5 S4 *disabled pci:0000:00:13.1 UHC6 S4 *disabled pci:0000:00:13.2 UHC7 S4 *disabled pci:0000:00:14.5 root@xbmc1:~# please also see my lsusb and my lspci below root@xbmc1:~# lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 002: ID 0471:060c Philips (or NXP) Consumer Infrared Transceiver (HP) Bus 005 Device 002: ID 1ea7:0002 root@xbmc1:~# root@xbmc1:~# lspci 00:00.0 Host bridge: Advanced Micro Devices [AMD] RS880 Host Bridge 00:02.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (ext gfx port 0) 00:0a.0 PCI bridge: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (PCIE port 5) 00:11.0 SATA controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 SATA Controller [IDE mode] 00:12.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:12.1 USB Controller: ATI Technologies Inc SB7x0 USB OHCI1 Controller 00:12.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:13.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:13.1 USB Controller: ATI Technologies Inc SB7x0 USB OHCI1 Controller 00:13.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 3c) 00:14.1 IDE interface: ATI Technologies Inc SB7x0/SB8x0/SB9x0 IDE Controller 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: ATI Technologies Inc SB7x0/SB8x0/SB9x0 LPC host controller 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 00:14.5 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI2 Controller 00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor HyperTransport Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Miscellaneous Control 00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Link Control 01:00.0 VGA compatible controller: nVidia Corporation GT218 [GeForce 210] (rev a2) 01:00.1 Audio device: nVidia Corporation High Definition Audio Controller (rev a1) 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) root@xbmc1:~# I have setup xbmc to suspend in settings and that work fine, however i cannot get it to wakeup, I see a red light on the MCE receiver when i press a button on the remote when the pc is supended, however it will not resume, the only way it will resume is if i press the power button on the pc case itself. Hopefully someone can point me in the right direction. Thanks |