Linux Openelec problem (handshake issue?) - Printable Version +- Kodi Community Forum (https://forum.kodi.tv) +-- Forum: Support (https://forum.kodi.tv/forumdisplay.php?fid=33) +--- Forum: General Support (https://forum.kodi.tv/forumdisplay.php?fid=111) +---- Forum: Linux (https://forum.kodi.tv/forumdisplay.php?fid=52) +---- Thread: Linux Openelec problem (handshake issue?) (/showthread.php?tid=170405) |
Openelec problem (handshake issue?) - Skank - 2013-08-02 I hope this is the right place.. Just installed a new fresh device. Mobo is Biostar NM70I-847 - Moederbord - mini ITX - Intel Celeron 847 - NM70 - Gigabit Ethernet - HD Graphics Running latest stable openelec build for intel The problem is this Normally i set it like this: Pc connected to pioneer vsx 919 (with hdmi) , then with hdmi connected to tv When i do this with my windows xbmc machine, everything works well But when i try this with my new openelec machine i dont get anythin on the screen As soon as i connect the openelec straight away to the tv with hdmi , i do get a picture (thats how i installed it) Without the pioneer inbetween.. How do i get it to work with my amplifier in between? Hdmi ports are correctly set up I think this is a handshake issue.. Tv is turned on first wi right hdmi port Then the pioneer with right hdmi port Then when all is started I turn on the htpc... RE: Openelec problem (handshake issue?) - Skank - 2013-08-02 Anyone? RE: Openelec problem (handshake issue?) - FernetMenta - 2013-08-03 you could motivate others looking into this by posting a debug log along with detailed information on what you did in order to produce this log. RE: Openelec problem (handshake issue?) - Skank - 2013-08-03 Huh? Debug log wont contain anything, cause i cant see anything.. Its no xbmc bug.. Did you read my post? RE: Openelec problem (handshake issue?) - fritsch - 2013-08-03 XBMC will enumerate the modes when it starts up. This can be seen in the logs. Also /usr /lib /xbmc /xbmc-xrandr will show that info. RE: Openelec problem (handshake issue?) - leepenny - 2013-08-03 (2013-08-03, 12:20)Skank Wrote: Huh? Debug log wont contain anything, cause i cant see anything.. What a nice forthcoming answer - post a log - it may not be of use to you - but may help you fix your problem by allowing others to see what your machine is up to ! RE: Openelec problem (handshake issue?) - Skank - 2013-08-04 Ok then but how should i do this then? Connect itlike it should, so htpc - pioneer - tv, but then i dont see a thing and cant get the log? Ot Connect it straight away htpc - tv, then i will see a log, but it wont show the problem... RE: Openelec problem (handshake issue?) - Milhouse - 2013-08-04 Reproduce the problem, so your first connection method, then connect with ssh and upload the log to pastebin.com with the command: Code: pastebinit -u /storage/.xbmc/temp/xbmc.log In case you don't know, the username is root and the default password is openelec. RE: Openelec problem (handshake issue?) - styx06 - 2013-08-04 Actually I am having the same problem....XBMC will only boot when the tv is on (although i am on XBMCbuntu). XBMC does not create any logs as it is not started. Last lineof my xbmc.log: Code: 10:41:25 T:3038467840 NOTICE: application stopped... After this I rebooted again with TV turned off, but no further logging. Xorg.0.log does provide some clues however: Code: [ 2.463] (II) intel(0): Output VGA1 has no monitor section So apparently X cannot find any monitor and closes the connection? RE: Openelec problem (handshake issue?) - Skank - 2013-08-04 (2013-08-04, 08:41)MilhouseVH Wrote: Reproduce the problem, so your first connection method, then connect with ssh and upload the log to pastebin.com with the command: Not sure if i enabled ssh during install.. Dont think so + i need ip adress too right? RE: Openelec problem (handshake issue?) - Skank - 2013-08-04 It says my connection is refused (ssh) RE: Openelec problem (handshake issue?) - Milhouse - 2013-08-04 Enable it in OpenELEC Settings, or edit /flash/extlinux.conf and add "ssh" to the end of the APPEND line ie: Code: APPEND boot=LABEL=System disk=LABEL=Storage quiet ssh Mount /flash read-write with "mount -o remount,rw /flash", edit extlinux.conf using vi or nano, then remount /flash read-only with "mount -o remount,ro /flash". RE: Openelec problem (handshake issue?) - Skank - 2013-08-05 i attached a second pc monitor to look what was wrong AND BINGO suddenly i have screen on the tv (with avr in between) and on the pc monitor I watched the video settings and they were on 1650x1080 or something like that refresh rate was 58.8 As soon as i set it to 1920x1080 , video was gone on tv but not on monitor getting back to lower resolution there was tv again... I couldnt believe my eyes cause 1920x1080p was working straight away on tv (without avr), and on windows its working with avr too on that resolution so i looked further And i changed refresh rate to 60 and resolution to 1920x1080p and TADAAAAAAAA Picture on tv ! Phew ! problem solved, so refresh rate should be on 60 right? not 58.88 |