asrock ion and hdpvr device .... - Printable Version +- Kodi Community Forum (https://forum.kodi.tv) +-- Forum: Support (https://forum.kodi.tv/forumdisplay.php?fid=33) +--- Forum: General Support (https://forum.kodi.tv/forumdisplay.php?fid=111) +---- Forum: Linux (https://forum.kodi.tv/forumdisplay.php?fid=52) +---- Thread: asrock ion and hdpvr device .... (/showthread.php?tid=78348) |
asrock ion and hdpvr device .... - linuxluemmel - 2010-08-03 I have a little issue with the lirc system on asrock ion : After a few hours of searching I have a almost running lirc system. The remote part of the drivers lirc_zilog works fine. I did a svn.checkout of v4l on sunday and patched the hdpvr driver sucessfull. I did a donwload for the lirc_zilog driver from a redhat-site. I can build on my custom kernel 2.6.33.6 sucessfull hdpvr / lirc_dev / lirc_zilog The remote is working properly (controlled by command irw) --------------------------------------------------------------------------------------------------- user@luxeria001:~$ irw 0000000000001796 00 Left hdpvr 0000000000001796 01 Left hdpvr 0000000000001796 00 Left hdpvr 0000000000001796 00 Left hdpvr 00000000000017a0 00 Ch+ hdpvr 00000000000017a1 00 Ch- hdpvr 00000000000017a1 01 Ch- hdpvr 0000000000001781 00 1 hdpvr 0000000000001781 00 1 hdpvr 00000000000017b5 00 Play hdpvr 00000000000017b4 00 Forward hdpvr 00000000000017b4 01 Forward hdpvr 00000000000017b2 00 Rewind hdpvr_________________________________________________________ If I do load lirc_dev prio to lirc_zilog I have a oops. If I load lirc_zilog direct wihtout prior loading lirc_dev it loads perfect .... Adding 995988k swap on /dev/sda5. Priority:-1 extents:1 across:995988k lirc_dev: IR Remote Control driver registered, major 61 lirc_zilog: Zilog/Hauppauge IR driver initializing lirc_zilog: chip found with RX and TX lirc_dev: lirc_register_driver: sample_rate: 0 Zilog/Hauppauge i2c IR 2-0071: firmware: requesting haup-ir-blaster.bin lirc_zilog: Zilog/Hauppauge IR blaster firmware version 2.1.0 loaded lirc_zilog: initialization complete I use a custom kernel 2.6.33.6 and on this link is the configuration file http://pastebin.ch/5899 My devices comes here : user@luxeria001:~$ ls -al /dev/lirc* crw-rw---- 1 root root 61, 0 2010-08-03 19:37 /dev/lirc0 lrwxrwxrwx 1 root root 19 2010-08-03 19:38 /dev/lircd -> /var/run/lirc/lircd user@luxeria001:~$ My configuration file comes here : # /etc/lirc/hardware.conf # #Chosen Remote Control REMOTE="hdpvr" REMOTE_MODULES="" REMOTE_DRIVER="" REMOTE_DEVICE="/dev/lirc0" REMOTE_SOCKET="" REMOTE_LIRCD_CONF="" REMOTE_LIRCD_ARGS="" #Chosen IR Transmitter TRANSMITTER="blaster" TRANSMITTER_MODULES="lirc_zilog" TRANSMITTER_DRIVER="" TRANSMITTER_DEVICE="" TRANSMITTER_SOCKET="/var/run/lirc/lircd1" TRANSMITTER_LIRCD_CONF="" TRANSMITTER_LIRCD_ARGS="" #Enable lircd START_LIRCD="true" #Don't start lircmd even if there seems to be a good config file #START_LIRCMD="false" #Try to load appropriate kernel modules LOAD_MODULES="" # Default configuration files for your hardware if any LIRCMD_CONF="" #Forcing noninteractive reconfiguration #If lirc is to be reconfigured by an external application #that doesn't have a debconf frontend available, the noninteractive #frontend can be invoked and set to parse REMOTE and TRANSMITTER #It will then populate all other variables without any user input #If you would like to configure lirc via standard methods, be sure #to leave this set to "false" FORCE_NONINTERACTIVE_RECONFIGURATION="false" START_LIRCMD="" user@luxeria001:/etc/lirc$ Every Time I try to send a simple command I get this .... user@luxeria001:~$ irsend -d /dev/lircd SEND_ONCE blaster 1_1_KEY_6 irsend: command failed: SEND_ONCE blaster 1_1_KEY_6 irsend: hardware does not support sending user@luxeria001:~$ Has someone a sugestion ? or a stupid hint ? |