[bmonster]

Morning Milhouse,

When I have a problem, i'll leave it a couple of day and see if it disappears on its own, if it doesn't I'll always check the problem still exists under a clean environment, basically rename the .kodi folder.
I've gone back and tried all builds from 0201 to 0210, and for me the only one that's not screwing with the memory is 0205, every other build is giving high memory usage with minutes of booting.

Sorry I'm not too technical, so not sure how to investigate further, I can help further with a little guidance.

Regards BM

Can you post your config.txt?

Also can you run "bcmstat.sh Zxd 10" in ssh after booting the latest build, as this should give a memory usage figure I can relate to. Leave it running and see if the memory usage figure increases to an abnormally high level.

My RPi3 with 320MB GPU split (booted last night about 9pm, so over 20 hours ago) currently shows:

Code:

Memory Free/Used
================
596,568 kB/15.2%

Once memory usage increases significantly, try running "top -o RES" which should list processes in descending order of memory usage.

Since this doesn't appear to be a new problem, and happens with a "clean" .kodi, I'd expect this to be far more widespread. I currently suspect this is something specific to your configuration, but not sure what that could be.

Hi Milhouse,

Its been running about 15mins on 0211, and its not gone much higher than 50%, better than 80%, but still seems high compared to your 15%.
I've added the requested info below, let me know if anything stands out to you.
If it starts rising again, i'll repost top -o RES

config.txt

Code:

force_turbo=0
hdmi_force_hotplug=1
hdmi_ignore_cec_init=1
avoid_warnings=1

gpu_mem=256
gpu_mem_256=112
gpu_mem_512=160
gpu_mem_1024=256

arm_freq=1200
core_freq=500
sdram_freq=500
over_voltage=2

decode_MPG2=
decode_WVC1=

bcmstat.sh Zxd 10

Code:

Config: v0.4.4, args "Zxd 10", priority lowest (+19)
   Board: 4 x ARMv7 cores available, ondemand governor (Pi3 rev 1.2, BCM2837 SoC with 1GB RAM by Embest)
  Memory: 1023MB (split 767MB ARM, 256MB GPU)
HW Block: |   ARM   |  Core  |  H264  |    SDRAM    |
Min Freq: |  600MHz | 250MHz |   0MHz |    500MHz   |
Max Freq: | 1200MHz | 500MHz | 300MHz |    500MHz   |
Voltages: |        +2, 1.3125V        | +2, 1.2500V |
   Other: temp_limit=85, hdmi_force_hotplug=1
Firmware: Feb 8 2017 19:38:24, version d61adb766e5712326bba636c81017fbac3b8419f (clean) (release)
  Codecs: H264 H263 WVC1 MPG4 MPG2 VP8 VP6 VORB THRA MJPG FLAC PCM
  Booted: Sat Feb 11 23:06:35 2017

Time         ARM    Core    H264 Core Temp (Max)  IRQ/s     RX B/s     TX B/s  %user  %nice   %sys  %idle  %iowt   %irq %s/irq %total Memory Free/Used
======== ======= ======= ======= =============== ====== ========== ========== ====== ====== ====== ====== ====== ====== ====== ====== ================
23:21:00 1200Mhz  500Mhz  300Mhz 55.31C (55.31C)    505          0          0   0.00   7.84  15.69  78.44   0.00   0.00   0.00  21.56 366,832 kB/52.3%

top -o RES

Code:

487 root      20   0  999644 525024 171864 S  26.3 68.3   7:46.27 kodi.bin
  262 root       9 -11   91620   5596   4812 S   0.0  0.7   0:00.16 pulseaudio
    1 root      20   0    6268   4852   3988 S   0.0  0.6   0:01.42 systemd
  471 root      20   0    6204   4648   4264 S   0.0  0.6   0:00.19 wpa_supplicant
  210 root      20   0   13700   3760   3524 S   0.0  0.5   0:00.28 systemd-journal
1144 root      20   0    4840   3756   3332 S   0.0  0.5   0:01.15 sshd
  357 root      20   0    5432   3712   3304 S   0.0  0.5   0:00.89 connmand
  364 root      20   0    4516   3520   3244 S   0.0  0.5   0:00.04 sshd
1145 root      20   0    4516   3244   3008 S   0.0  0.4   0:00.23 sshd
  258 root      20   0    4544   3224   3032 S   0.0  0.4   0:00.03 systemd-logind
  270 dbus      20   0    4036   2716   2392 S   0.0  0.4   0:00.24 dbus-daemon
  252 root      20   0    8316   2616   2144 S   0.0  0.3   0:00.18 systemd-udevd
  559 root      20   0    3264   2280   1632 S   0.0  0.3   0:00.17 mount.ntfs
  243 root      20   0    3496   2028   1844 S   0.0  0.3   0:00.17 rpcbind
  600 root      20   0    3076   1996   1608 S   0.0  0.3   0:00.00 mount.ntfs
  597 root      20   0    3156   1920   1524 S   0.0  0.2   0:00.52 mount.ntfs
1151 root      20   0    2920   1856   1480 R   1.3  0.2   0:00.65 top
  254 root      20   0    2996   1820   1628 S   0.0  0.2   0:00.05 eventlircd
1148 root      20   0    2756   1708   1612 S   0.0  0.2   0:00.00 sh
  482 root      20   0    2756   1652   1548 S   0.0  0.2   0:00.00 kodi.sh
1147 root      20   0    2080   1152   1088 S   0.0  0.1   0:00.00 sftp-server
1146 root      20   0    2756    376    344 S   0.0  0.0   0:00.00 sh
    2 root      20   0       0      0      0 S   0.0  0.0   0:00.00 kthreadd
    3 root      20   0       0      0      0 S   0.0  0.0   0:01.11 ksoftirqd/0
    5 root       0 -20       0      0      0 S   0.0  0.0   0:00.00 kworker/0:0H
    6 root      20   0       0      0      0 S   0.0  0.0   0:00.04 kworker/u8:0
    7 root      20   0       0      0      0 S   0.0  0.0   0:00.38 rcu_sched
    8 root      20   0       0      0      0 S   0.0  0.0   0:00.00 rcu_bh
    9 root      rt   0       0      0      0 S   0.0  0.0   0:00.00 migration/0
   10 root       0 -20       0      0      0 S   0.0  0.0   0:00.00 lru-add-drain
   11 root      rt   0       0      0      0 S   0.0  0.0   0:00.00 watchdog/0
   12 root      20   0       0      0      0 S   0.0  0.0   0:00.00 cpuhp/0

After 1hr

Code:

┌────────────────────────────────────────────────────────────────────┐
     │                         • MobaXterm 9.4 •                          │
     │            (SSH client, X-server and networking tools)             │
     │                                                                    │
     │ ➤ SSH session to [email protected]                                │
     │   • SSH compression : ✔                                            │
     │   • SSH-browser     : ✔                                            │
     │   • X11-forwarding  : ✘  (disabled or not supported by server)     │
     │   • DISPLAY         : 192.168.1.102:0.0                            │
     │                                                                    │
     │ ➤ For more info, ctrl+click on help or visit our website           │
     └────────────────────────────────────────────────────────────────────┘

##############################################
#                 LibreELEC                  #
#            http://libreelec.tv             #
##############################################

LibreELEC (community) Version: devel-20170211224117-#0211-g2c59d7d
LibreELEC git: 2c59d7d424228ded592d953efa8f484753837f87
KODI:~ # top -o RES
top - 01:21:45 up  1:13,  1 user,  load average: 0.20, 1.85, 1.47
Tasks: 140 total,   2 running, 138 sleeping,   0 stopped,   0 zombie
%Cpu(s):  2.0 us,  0.7 sy,  1.3 ni, 96.1 id,  0.0 wa,  0.0 hi,  0.0 si,  0.0 st
KiB Mem :   768548 total,    31112 free,   544284 used,   193152 buff/cache
KiB Swap:        0 total,        0 free,        0 used.   170124 avail Mem

  PID USER      PR  NI    VIRT    RES    SHR S  %CPU %MEM     TIME+ COMMAND
  485 root      20   0 1120444 544228  30308 R  23.0 70.8  26:20.52 kodi.bin
2397 root      20   0    4836   3560   3120 S   0.0  0.5   0:01.18 sshd
2398 root      20   0    4516   3244   3008 S   0.0  0.4   0:00.19 sshd
    1 root      20   0    6300   2760   1860 S   0.0  0.4   0:01.53 systemd
  354 root      20   0    5432   2276   1864 S   0.0  0.3   0:00.86 connmand
  454 root      20   0    6204   2024   1640 S   0.0  0.3   0:00.48 wpa_supplicant
2404 root      20   0    2924   1856   1476 R   1.3  0.2   0:01.40 top
  219 root      20   0   13700   1768   1528 S   0.0  0.2   0:00.38 systemd-journal
2401 root      20   0    2756   1568   1472 S   0.0  0.2   0:00.02 sh
  270 dbus      20   0    4036   1164    800 S   0.0  0.2   0:00.46 dbus-daemon
2400 root      20   0    2080   1056    992 S   0.0  0.1   0:00.00 sftp-server
  326 root       9 -11   91620   1044    264 S   0.0  0.1   0:00.15 pulseaudio
  612 root      20   0    3076    872    396 S   0.0  0.1   0:00.01 mount.ntfs
  266 root      20   0    4544    836    644 S   0.0  0.1   0:00.06 systemd-logind
  254 root      20   0    8500    832    276 S   0.0  0.1   0:00.21 systemd-udevd
  567 root      20   0    3076    688    172 S   0.0  0.1   0:00.02 mount.ntfs
  359 root      20   0    4516    672    396 S   0.0  0.1   0:00.07 sshd
  564 root      20   0    3064    648    268 S   0.0  0.1   0:00.00 mount.ntfs
  325 root      20   0    2996    556    364 S   0.0  0.1   0:00.07 eventlircd
2399 root      20   0    2756    368    336 S   0.0  0.0   0:00.00 sh
  481 root      20   0    2756    364    260 S   0.0  0.0   0:00.00 kodi.sh
  242 root      20   0    3496    184      0 S   0.0  0.0   0:00.19 rpcbind
    2 root      20   0       0      0      0 S   0.0  0.0   0:00.00 kthreadd
    3 root      20   0       0      0      0 S   0.0  0.0   0:03.54 ksoftirqd/0
    5 root       0 -20       0      0      0 S   0.0  0.0   0:00.00 kworker/0:0H
    7 root      20   0       0      0      0 S   0.0  0.0   0:01.16 rcu_sched
    8 root      20   0       0      0      0 S   0.0  0.0   0:00.00 rcu_bh
    9 root      rt   0       0      0      0 S   0.0  0.0   0:00.00 migration/0
   10 root       0 -20       0      0      0 S   0.0  0.0   0:00.00 lru-add-drain
   11 root      rt   0       0      0      0 S   0.0  0.0   0:00.01 watchdog/0
   12 root      20   0       0      0      0 S   0.0  0.0   0:00.00 cpuhp/0
   13 root      20   0       0      0      0 S   0.0  0.0   0:00.00 cpuhp/1

[MONSTA]

Click the "Defaults" button

You were right. Reset to default seems solved the issue . Connection activates with a delay of a few seconds, but it works anyway.
Thank you.

[HiassofT]

[*]Unmerged PR:1313 (config scripts for Wolfson/Cirrus Logic audio card) converted to package

Just wanted to report back that it's working fine. Tested on RPi model B with Wolfson card and RPi2 with Cirrus Logic card. Thanks!

so long,

Hias

[Milhouse]

Hi Milhouse,

Its been running about 15mins on 0211, and its not gone much higher than 50%, better than 80%, but still seems high compared to your 15%.
I've added the requested info below, let me know if anything stands out to you.
If it starts rising again, i'll repost top -o RES

Are you using more than the default cache memory? Can you post your kodi.log (as this will include your advancedsettings.xml).

[bmonster]

Hi Milhouse,

Its been running about 15mins on 0211, and its not gone much higher than 50%, better than 80%, but still seems high compared to your 15%.
I've added the requested info below, let me know if anything stands out to you.
If it starts rising again, i'll repost top -o RES

Are you using more than the default cache memory? Can you post your kodi.log (as this will include your advancedsettings.xml).

Morning Milhouse,

Firstly thanks for your time on this.

kodi.log:

https://drive.google.com/open?id=0BwAs5I...2tBN0Y4UkU

top -o RES this morning after 8hours

Code:

┌────────────────────────────────────────────────────────────────────┐
     │                         • MobaXterm 9.4 •                          │
     │            (SSH client, X-server and networking tools)             │
     │                                                                    │
     │ ➤ SSH session to [email protected]                                │
     │   • SSH compression : ✔                                            │
     │   • SSH-browser     : ✔                                            │
     │   • X11-forwarding  : ✘  (disabled or not supported by server)     │
     │   • DISPLAY         : 192.168.1.102:0.0                            │
     │                                                                    │
     │ ➤ For more info, ctrl+click on help or visit our website           │
     └────────────────────────────────────────────────────────────────────┘

##############################################
#                 LibreELEC                  #
#            http://libreelec.tv             #
##############################################

LibreELEC (community) Version: devel-20170211224117-#0211-g2c59d7d
LibreELEC git: 2c59d7d424228ded592d953efa8f484753837f87
KODI:~ # top -o RES
top - 11:20:35 up  7:31,  1 user,  load average: 0.21, 0.31, 0.36
Tasks: 139 total,   2 running, 137 sleeping,   0 stopped,   0 zombie
%Cpu(s):  1.9 us,  0.9 sy,  2.2 ni, 95.0 id,  0.0 wa,  0.0 hi,  0.0 si,  0.0 st
KiB Mem :   768548 total,    39020 free,   490892 used,   238636 buff/cache
KiB Swap:        0 total,        0 free,        0 used.   222640 avail Mem

  PID USER      PR  NI    VIRT    RES    SHR S  %CPU %MEM     TIME+ COMMAND
  498 root      20   0 1045228 480088  20020 S  25.8 62.5 128:21.30 kodi.bin
4265 root      20   0    4840   3676   3244 S   0.0  0.5   0:01.15 sshd
4266 root      20   0    4516   3208   2972 S   0.0  0.4   0:00.19 sshd
  215 root      20   0   13700   2496   2260 S   0.0  0.3   0:00.71 systemd-journal
  454 root      20   0    6204   2424   2044 S   0.0  0.3   0:02.11 wpa_supplicant
  334 root      20   0    5432   2248   1832 S   0.0  0.3   0:02.82 connmand
    1 root      20   0    6208   2116   1248 S   0.0  0.3   0:01.77 systemd
4272 root      20   0    2924   1852   1476 R   1.3  0.2   0:00.11 top
  571 root      20   0    3672   1656    552 S   0.0  0.2   0:38.01 mount.ntfs
4269 root      20   0    2756   1632   1536 S   0.0  0.2   0:00.01 sh
  449 root      20   0    4516   1312   1036 S   0.0  0.2   0:00.06 sshd
  568 root      20   0    3064   1300    828 S   0.0  0.2   0:06.90 mount.ntfs
  295 root       9 -11   91620   1236    452 S   0.0  0.2   0:00.16 pulseaudio
4268 root      20   0    2080   1120   1056 S   0.0  0.1   0:00.00 sftp-server
  258 dbus      20   0    4036   1096    716 S   0.0  0.1   0:01.82 dbus-daemon
  256 root      20   0    8400   1044    524 S   0.0  0.1   0:00.27 systemd-udevd
  549 root      20   0    3076    956    488 S   0.0  0.1   0:00.01 mount.ntfs
  292 root      20   0    4544    904    712 S   0.0  0.1   0:00.19 systemd-logind
  287 root      20   0    2996    724    532 S   0.0  0.1   0:00.12 eventlircd
  247 root      20   0    3496    652    456 S   0.0  0.1   0:00.23 rpcbind
  493 root      20   0    2756    448    344 S   0.0  0.1   0:00.00 kodi.sh
4267 root      20   0    2756    376    344 S   0.0  0.0   0:00.00 sh
    2 root      20   0       0      0      0 S   0.0  0.0   0:00.01 kthreadd
    3 root      20   0       0      0      0 S   0.0  0.0   0:09.71 ksoftirqd/0
    5 root       0 -20       0      0      0 S   0.0  0.0   0:00.00 kworker/0:0H
    6 root      20   0       0      0      0 S   0.0  0.0   0:00.39 kworker/u8:0
    7 root      20   0       0      0      0 R   0.0  0.0   0:04.25 rcu_sched
    8 root      20   0       0      0      0 S   0.0  0.0   0:00.00 rcu_bh
    9 root      rt   0       0      0      0 S   0.0  0.0   0:00.00 migration/0
   10 root       0 -20       0      0      0 S   0.0  0.0   0:00.00 lru-add-drain
   11 root      rt   0       0      0      0 S   0.0  0.0   0:00.14 watchdog/0
   12 root      20   0       0      0      0 S   0.0  0.0   0:00.00 cpuhp/0

Regards Bucky...

[popcornmix]

kodi.log:

https://drive.google.com/open?id=0BwAs5I...2tBN0Y4UkU

You'll need to enable debug logging in system settings. Then reboot. Then grab the log.

[bmonster]

kodi.log:

https://drive.google.com/open?id=0BwAs5I...2tBN0Y4UkU

You'll need to enable debug logging in system settings. Then reboot. Then grab the log.

Here you go, debug enabled.

https://drive.google.com/open?id=0BwAs5I...FpqX2xDR0E

Thank you

[Milhouse]

Here you go, debug enabled.

https://drive.google.com/open?id=0BwAs5I...FpqX2xDR0E

Thank you

OK, so no extra file caching.

Are you absolutely certain this happens with a clean ".kodi"? I see you're using a third-party skin, a PVR addon and quite a few other addons/scripts.

Can you paste the bcmstat.sh output as follows:

Code:

systemctl stop kodi
mv /storage/.kodi /storage/.kodi.bak
reboot
<wait for the system to restart>
bcmstat.sh -Zxd 10

Paste a link to the output of bcmstat.sh once 2-3 minutes worth of data has been collected.

[bmonster]

Here you go, debug enabled.

https://drive.google.com/open?id=0BwAs5I...FpqX2xDR0E

Thank you

OK, so no extra file caching.

Are you absolutely certain this happens with a clean ".kodi"? I see you're using a third-party skin, a PVR addon and quite a few other addons/scripts.

Can you paste the bcmstat.sh output as follows:

Code:

systemctl stop kodi
mv /storage/.kodi /storage/.kodi.bak
reboot
<wait for the system to restart>
bcmstat.sh -Zxd 10

Paste a link to the output of bcmstat.sh once 2-3 minutes worth of data has been collected.

Will do, I'm just getting a new sd card sorted and will do a proper clean/fresh install, and will get back to you.

And yer, i use estuary mod, which uses a ton of different scripts.

[Szymon_Zy]

Milhouse does your recent builds include AudioDSP support? I can't find its settings in audio menu durging movie playback. I need to boost center channel in downmixed audio.

[popcornmix]

Milhouse does your recent builds include AudioDSP support? I can't find its settings in audio menu durging movie playback. I need to boost center channel in downmixed audio.

ADSP doesn't currently work.
But these builds include "Boost centre channel when downmixing" in system/audio settings.

[Milhouse]

New LibreELEC.tv Leia build #0212: RPi / RPi2
(Supercedes previous build)

Code:

# uname -a
Linux rpi512 4.9.9 #1 Sun Feb 12 23:27:19 GMT 2017 armv6l GNU/Linux

# vcgencmd version
Feb  8 2017 19:38:24
Copyright (c) 2012 Broadcom
version d61adb766e5712326bba636c81017fbac3b8419f (clean) (release)

# lsb_release
LibreELEC (Milhouse) - Version: devel-20170212232610-#0212-g7fec979 [Build #0212]

# Kodi version
(18.0-ALPHA1 Git:4c792db). Platform: Linux ARM 32-bit

Based on tip of LibreELEC.tv master (7fec979f, changelog) and tip of XBMC master (99c25f60, changelog) with the following modifications:

• Includes newclock5 patches
  
• Excludes the LibreELEC linux-01-RPi_support patch in favour of sourcing these and possibly more recent patches directly from kernel branch rpi-4.9.y
  
• Includes latest bcm2835-driver next (4d81cd6f, ahead +652)
  
• Includes latest kodi-platform master (c8188d82)
  
• Includes latest libcec master (0a97062d, ahead +22)
  
• Includes latest libnfs master (91421265, ahead +48)
  
• Includes latest p8-platform master (2d90f986, ahead +9)
  
• Includes latest addons: inputstream.adaptive (a347296e), inputstream.rtmp (55437ac7), peripheral.joystick (69c9e5fe, +1), pvr.argustv (5a36c586), pvr.demo (8243935f), pvr.dvblink (0015079e), pvr.dvbviewer (9fb34b3c), pvr.filmon (315e5034), pvr.hdhomerun (98cb8d40), pvr.hts (1caa390d, +1), pvr.iptvsimple (53d63cce), pvr.mediaportal.tvserver (019c7e99), pvr.mythtv (d03a5390, +3), pvr.nextpvr (cb1b5415), pvr.njoy (080cd321), pvr.octonet (8549a31c), pvr.pctv (e67e9695), pvr.stalker (a609149c), pvr.vbox (dea8335a), pvr.vdr.vnsi (7033621d), pvr.vuplus (6ff2eb28), pvr.wmc (5f1db43f)
  
• Include [env] afbd134f: linux: Enable Fair Queue packet scheduling (TEST)
  
• Include [env] e533a8be: linux: Default to CONFIG_TCP_CONG_BBR (TEST)
  
• Include [env] patch: repository.retroplayer.libreelec.addons: add temp repo for testing
  
• Include [env] patch: Bump included addon versions to prevent online updates
  
• Include [env] patch: Don't build ADSP addons
  
• Include [env] patch: iwlwifi-firmware: update to iwlwifi-firmware-ba301aa
  
• Include [env] patch: linux: enable in-tree rtl8192cu for RPi/RPi2
  
• Include [env] patch: Add kodi binary addons (pvr, adsp, other)
  
• Include [env] patch: Add experimental splash video for RPi
  
• Include [env] patch: HACK: Disable multiple PVR addons during migration. Always enable inputstream.* and os.*
  
• Include [env] PR:1287: virtio-gpu support (qemu/kvm)
  
• Include [env] PR:1326: Build system scripts cleanup
  
• Include [env] PR:1327: [master] input: change input repeat config
  
• Include [env] PR:1329: imagedecoder.raw: add add-on
  
• Include [pkg] patch: alsa-lib: conf: Add card config for Intel HDMI/DP LPE audio (alsa-lib)
  
• Include [pkg] PR:11163: Fix silent failure when game add-on can't be installed
  
• Revert [pkg] PR:8966/commits/8d88a547041a2a540bff5217c3b19ffdc4473038: hack: add iso to filedirectory list (Reason: causes navigation/playback issues) (kodi)
  

Build Highlights:

1. VideoPlayer: fix edl skipping
   
2. PR:1327: [master] input: change input repeat config
   
3. PR:1329: imagedecoder.raw: add add-on
   

Build Details:

1. LibreELEC.tv:
   • docker: update to 1.13.1 (PR:1307, 4 commits, 6 files changed)
     
   • linux-amlogic: update to 83803a1 (PR:1321, 1 commit, 1 file changed)
     
   • linux: update to linux-4.9.9 (PR:1314, 4 commits, 7 files changed)
     
   • add config scripts for RPi Wolfson/Cirrus Logic audio card (PR:1313, 2 commits, 7 files changed)
     
2. XBMC:
   • Improve performance for python addons using xbmcgui.ListItem (PR:11651, 2 commits, 2 files changed)
     
   • VideoPlayer: fix edl skipping (PR:11646, 3 commits, 7 files changed)
     
   • [interfaces] legacy: fix format error when building with -Werror=form… (PR:11656, 1 commit, 1 file changed)
     
3. newclock5:
   • New commits in this build:
     • mmm (b08cd0cf)
       
     • mm (90165774)
       
     • Revert "mm" (33332086)
       
     • Revert "mmm" (0e64fd71)
       
     • OMXPlayer: Fixup after DVDMessage changes (0ffe036f)
       
   • Commits no longer in build:
     • Application: Add decay before python door closes (7066e497)
       
     • Application: Allow python door to open for up to 80ms (5d6c8abf)
       
4. Additional commits/pull requests/changes not yet merged upstream:
   • Updated: [env] patch: Add kodi binary addons (pvr, adsp, other)
     
   • Added: [env] PR:1326: Build system scripts cleanup
     
   • Added: [env] PR:1327: [master] input: change input repeat config
     
   • Added: [env] PR:1329: imagedecoder.raw: add add-on
     

[Xeno22]

Could there be any reason why the info button does not open the media info screen?

Also: If I try to install a new addon from a repo that does not exist anymore, there is no notification about that 404 error - kodi just says nothing.

[Milhouse]

Could there be any reason why the info button does not open the media info screen?

Maybe you don't have the scraper add-on installed on the device that has been used to scrape the metadata?

[Milhouse]

New LibreELEC.tv Leia build #0213: RPi / RPi2
(Supercedes previous build)

Code:

# uname -a
Linux rpi512 4.9.9 #1 Mon Feb 13 21:28:28 GMT 2017 armv6l GNU/Linux

# vcgencmd version
Feb 13 2017 18:18:45
Copyright (c) 2012 Broadcom
version ced92b8255b84e8bf45f318abd99a285dcfc9e7e (clean) (release)

# lsb_release
LibreELEC (Milhouse) - Version: devel-20170213212658-#0213-g7fec979 [Build #0213]

# Kodi version
(18.0-ALPHA1 Git:4c792db). Platform: Linux ARM 32-bit

Based on tip of LibreELEC.tv master (7fec979f, changelog) and tip of XBMC master (25f596dc, changelog) with the following modifications:

• Includes newclock5 patches
  
• Excludes the LibreELEC linux-01-RPi_support patch in favour of sourcing these and possibly more recent patches directly from kernel branch rpi-4.9.y
  
• Includes latest bcm2835-driver next (86e7c81c, ahead +653)
  
• Includes latest kodi-platform master (c8188d82)
  
• Includes latest libcec master (0a97062d, ahead +22)
  
• Includes latest libnfs master (91421265, ahead +48)
  
• Includes latest p8-platform master (2d90f986, ahead +9)
  
• Includes latest addons: inputstream.adaptive (a347296e), inputstream.rtmp (55437ac7), peripheral.joystick (69c9e5fe, +1), pvr.argustv (5a36c586), pvr.demo (8243935f), pvr.dvblink (0015079e), pvr.dvbviewer (9fb34b3c), pvr.filmon (315e5034), pvr.hdhomerun (98cb8d40), pvr.hts (1caa390d, +1), pvr.iptvsimple (53d63cce), pvr.mediaportal.tvserver (019c7e99), pvr.mythtv (d03a5390, +3), pvr.nextpvr (cb1b5415), pvr.njoy (080cd321), pvr.octonet (8549a31c), pvr.pctv (e67e9695), pvr.stalker (a609149c), pvr.vbox (dea8335a), pvr.vdr.vnsi (7033621d), pvr.vuplus (6ff2eb28), pvr.wmc (5f1db43f)
  
• Include [env] afbd134f: linux: Enable Fair Queue packet scheduling (TEST)
  
• Include [env] e533a8be: linux: Default to CONFIG_TCP_CONG_BBR (TEST)
  
• Include [env] patch: repository.retroplayer.libreelec.addons: add temp repo for testing
  
• Include [env] patch: Bump included addon versions to prevent online updates
  
• Include [env] patch: Don't build ADSP addons
  
• Include [env] patch: iwlwifi-firmware: update to iwlwifi-firmware-ba301aa
  
• Include [env] patch: linux: enable in-tree rtl8192cu for RPi/RPi2
  
• Include [env] patch: Add kodi binary addons (pvr, adsp, other)
  
• Include [env] patch: Add experimental splash video for RPi
  
• Include [env] patch: HACK: Disable multiple PVR addons during migration. Always enable inputstream.* and os.*
  
• Include [env] PR:1287: virtio-gpu support (qemu/kvm)
  
• Include [env] PR:1326: Build system scripts cleanup
  
• Include [env] PR:1329: imagedecoder.raw: add add-on
  
• Include [env] PR:1330: v4l-utils: update to 1.12.2
  
• Include [pkg] patch: alsa-lib: conf: Add card config for Intel HDMI/DP LPE audio (alsa-lib)
  
• Include [pkg] PR:11163: Fix silent failure when game add-on can't be installed
  
• Include [pkg] PR:11668: FFmpegImage: Document and change alignment
  
• Revert [pkg] PR:8966/commits/8d88a547041a2a540bff5217c3b19ffdc4473038: hack: add iso to filedirectory list (Reason: causes navigation/playback issues) (kodi)
  

Build Highlights:

1. New firmware (gpuserv; remove CEC cleanup 12)
   
2. Mark used PLLs as critical - fix for JustBoom on RPi0
   
3. FFmpegImage: Document and change alignment
   
4. Drop PR:1327 ([master] input: change input repeat config)
   

Build Details:

1. Firmware (Feb 13):
   • firmware: gpuserv: Add new vchiq service for executing vpu and qpu jobs
     
   • firmware: Revert Redo CEC code cleanup 12: CEC init @ HPD. See: link
     
   • firmware: IL video_encode: Fix lockup with minimise fragmentation. See: link
     
2. XBMC:
   • OMXPlayer: Fixup after DVDMessage changes (PR:11666, 1 commit, 2 files changed)
     
   • Amltiming fr3 (PR:11667, 6 commits, 13 files changed)
     
   • Add dialog for delayed axis detection (PR:11623, 2 commits, 13 files changed)
     
3. newclock5:
   • Commits no longer in build:
     • mmm (b08cd0cf)
       
     • mm (90165774)
       
     • Revert "mm" (33332086)
       
     • Revert "mmm" (0e64fd71)
       
     • OMXPlayer: Fixup after DVDMessage changes (0ffe036f)
       
4. kernel 4.9.y:
   • New commits in this build:
     • dwc_otg: fix summarize urb->actual_length for isochronous transfers (7e7b6947)
       
     • clk-bcm2835: Mark used PLLs and dividers CRITICAL (9937447f)
       
5. Additional commits/pull requests/changes not yet merged upstream:
   • Added: [env] PR:1330: v4l-utils: update to 1.12.2
     
   • Added: [pkg] PR:11668: FFmpegImage: Document and change alignment