Posts: 4
Joined: Dec 2010
Reputation:
0
Hi fellas,
I recently installed xmbc Dharma Release Candidate 2, and I can't hear the audio from the HDMI cable. I tried to configure various configuration files, but at most I could hear noises "crackling". Does anyone know what and how to properly configure? The motherboard is a sapphire am3rs785g with the ATI Radeon HD 4200 (Microsoft Support DX 10.1) and the Realtek ALC662 HD Audio CODEC with 6-Channel. Obviously, the channels are not muted. Thanks in advance, Massimo
Posts: 35
Joined: Dec 2010
Reputation:
0
I have been struggling to get audio over HDMI to work too. I haven't booted into Windows in so long I don't remember if it did work on Windows either. In my opinion, you'll have to use an audio out and NOT over hdmi.....I don't even believe many of the lower end graphics cards support audio over hdmi in linux.
Posts: 4
Joined: Dec 2010
Reputation:
0
Hannas,
I download XBMC-dharma2.iso but in the prompt and in the install menu I see always "XBMCLive".
This is the output of the command that you request me :
APLAY -L
null
Discard all samples (playback) or generate zero samples (capture)
default:CARD=SB
HDA ATI SB, ALC662 rev1 Analog
Default Audio Device
front:CARD=SB,DEV=0
HDA ATI SB, ALC662 rev1 Analog
Front speakers
surround40:CARD=SB,DEV=0
HDA ATI SB, ALC662 rev1 Analog
4.0 Surround output to Front and Rear speakers
surround41:CARD=SB,DEV=0
HDA ATI SB, ALC662 rev1 Analog
4.1 Surround output to Front, Rear and Subwoofer speakers
surround50:CARD=SB,DEV=0
HDA ATI SB, ALC662 rev1 Analog
5.0 Surround output to Front, Center and Rear speakers
surround51:CARD=SB,DEV=0
HDA ATI SB, ALC662 rev1 Analog
5.1 Surround output to Front, Center, Rear and Subwoofer speakers
surround71:CARD=SB,DEV=0
HDA ATI SB, ALC662 rev1 Analog
7.1 Surround output to Front, Center, Side, Rear and Woofer speakers
iec958:CARD=SB,DEV=0
HDA ATI SB, ALC662 rev1 Digital
IEC958 (S/PDIF) Digital Audio Output
hdmi:CARD=HDMI
HDA ATI HDMI, ATI HDMI
HDMI Audio Output
---------------------------------------------------
aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: SB [HDA ATI SB], device 0: ALC662 rev1 Analog [ALC662 rev1 Analog]
Subdevices: 0/1
Subdevice #0: subdevice #0
card 0: SB [HDA ATI SB], device 1: ALC662 rev1 Digital [ALC662 rev1 Digital]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: HDMI [HDA ATI HDMI], device 3: ATI HDMI [ATI HDMI]
Subdevices: 1/1
Subdevice #0: subdevice #0
I hope in your skills !!!
Ciao,
Massimo
Posts: 4
Joined: Dec 2010
Reputation:
0
I try with mythbuntu and the audio over hdmi works fine with this /etc/asound.conf:
pcm.!default {
type hw
card 1
device 3
}
Now I'll try to reinstall dharma (because in myth my remote control doesn't works fine) in order to check it as describe above.
Ciao,
Massimo