OpenELEC Testbuilds for RaspberryPi Part 3 (Kodi 14.0) - Printable Version +- Kodi Community Forum (https://forum.kodi.tv) +-- Forum: Support (https://forum.kodi.tv/forumdisplay.php?fid=33) +--- Forum: General Support (https://forum.kodi.tv/forumdisplay.php?fid=111) +---- Forum: Raspberry Pi (https://forum.kodi.tv/forumdisplay.php?fid=166) +---- Thread: OpenELEC Testbuilds for RaspberryPi Part 3 (Kodi 14.0) (/showthread.php?tid=192380) Pages:
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
|
RE: OpenELEC Testbuilds for RaspberryPi Part 3 - HiassofT - 2014-12-04 (2014-12-03, 16:22)HiassofT Wrote: dvdplayer seems to have problems with some files: video freezes some 2-4 seconds before the end but audio continues to play. With omxplayer everything's fine.Some more tests: This also happens with Youtube videos. A nice testcase is "The EEVblog bunker" in the 720p version (as default on the pi), the video is quite shaky at the very end: https://www.youtube.com/watch?v=aeCyhWSPqfc I went through the old builds and 0901 plays it fine, with 0902 the video freezes shortly before the end (later than with the current builds, so not clearly visible with the sample in my previous post). Not sure if this info is helpful, that was the switch from newclock3 to newclock4... so long, Hias RE: OpenELEC Testbuilds for RaspberryPi Part 3 - popcornmix - 2014-12-04 @HiassofT I could reproduce the issue with the posted mp4 file. Not sure yet what the cause is. Is it always a few second before end of file, or does it ever stall in middle of file? E.g. if you have a file that is 42m30 long and it stops at 42m25, and you cut it down to 5m30, would you expect this file to stop at 5m25? RE: OpenELEC Testbuilds for RaspberryPi Part 3 - Jönke - 2014-12-04 (2014-12-03, 14:58)Milhouse Wrote:(2014-12-03, 09:54)Jönke Wrote: @Milhouse any chance you could include https://github.com/xbmc/xbmc/pull/5869 so i can help xhaggi to test it ? Thanks ! PR works perfect RE: OpenELEC Testbuilds for RaspberryPi Part 3 - HiassofT - 2014-12-04 (2014-12-04, 15:21)popcornmix Wrote: Is it always a few second before end of file, or does it ever stall in middle of file?It's always a few seconds before the end of the file, so far I haven't seen a stall in the middle. It's quite visible with the streams from the ORF TVthek as they usually cut down shows into multiple pieces. Also interesting: with these files the time-display/progress bar ("i" key) also freezes a few seconds before the end, both with dvdplayer and omxplayer. Cutting down a video doesn't change the stop point (eg 5 seconds before the end). I downloaded a video file from the ORF TVthek ("Missed a show" -> "Di 02.12.2014" -> "22.05 Uhr Willkommen Österreich" -> "Gags, Gags, Gags" - then use wget with the URL in kodi.log), its 14:29 long and then I cut off the first 800 seconds: Code: avconv -i in.mp4 -acodec copy -vcodec copy -ss 800 out.mp4 so long, Hias RE: OpenELEC Testbuilds for RaspberryPi Part 3 - eikman2k - 2014-12-04 Where could i find the Openelec Crash Log Support, i habe the Problem that my whole Pi freezes sometimes by watching a internet Stream Movie in Full HD.. @ first the sound stutters, than the picture stutters and finally the whole system freezes. is this a known bug? RE: OpenELEC Testbuilds for RaspberryPi Part 3 - popcornmix - 2014-12-04 (2014-12-04, 17:18)eikman2k Wrote: Where could i find the Openelec Crash Log Support, i habe the Problem that my whole Pi freezes sometimes by watching a internet Stream Movie in Full HD.. Not a known bug. Would be useful to know if kodi hangs or crashes (is picture or kodi gui still on screen?) Is Pi crashed? (can you ssh in?) A debug enabled log, dmesg output after the crash, and the crash dump (assuming kodi did crash) may explain the problem. If you are overclocking then disable that as the first test. Measuring voltage on board is also recommended as that is a common cause of crashes. RE: OpenELEC Testbuilds for RaspberryPi Part 3 - HiassofT - 2014-12-04 Some more tests on the video freeze issue: The files play fine with kodi git on my Linux box (Debian Wheezy 64bit) and with OpenELEC 4.97.1 generic i386 version on another PC, both with software decode and hardware acceleration (VDPAU). so long, Hias RE: OpenELEC Testbuilds for RaspberryPi Part 3 - Forage - 2014-12-04 (2014-12-04, 01:15)Milhouse Wrote: New OpenELEC Helix build: #1203Note that I lost most of my settings after updating #1202 to #1203. Basically all settings in the Kodi settings section have been reset to default. Things like library sources, it's entries and plugin settings remained. Nothing more I can add to it I think. Too late for a debug log and I already changed all the settings back again. RE: OpenELEC Testbuilds for RaspberryPi Part 3 - Milhouse - 2014-12-05 (2014-12-04, 22:16)Forage Wrote: Note that I lost most of my settings after updating #1202 to #1203. I think I'm noticing this myself, but haven't been able to pin down an exact cause (yet). I suspect the settings may be being "lost" during shutdown (power off), but need to do more testing. If you can pin it down that would be great. At the very least I would suggest applying your settings then taking a backup (cp guisettings.xml guisettings.xml.bak) so that you can quickly restore your settings if you lose them again. RE: OpenELEC Testbuilds for RaspberryPi Part 3 - allan87 - 2014-12-05 I lost my guisettings.xml recently as well, but it occurred in the process of updating to an official beta - rPi openelect beta 4 or 5, if I recall correctly. RE: OpenELEC Testbuilds for RaspberryPi Part 3 - Milhouse - 2014-12-05 New OpenELEC Helix build: #1204 (Supercedes previous build) Code: # uname -a Based on tip of OpenELEC master (707e6ae5, changelog) and tip of XBMC master (bc03a7c6, changelog) with the following modifications:
RE: OpenELEC Testbuilds for RaspberryPi Part 3 - Milhouse - 2014-12-05 A 4 second black splash animation video is available - see this post for sample. To install the 4 second black animation: Code: wget http://netlir.dk/rbej/builds/MilhouseVH/other/splash_4s_black.h264.bin -O /storage/.cache/splash.h264 To restore the original 6 second white animation (assuming you don't make a backup): Code: wget http://netlir.dk/rbej/builds/MilhouseVH/other/splash.h264.bin -O /storage/.cache/splash.h264 RE: OpenELEC Testbuilds for RaspberryPi Part 3 - Solo0815 - 2014-12-05 If you are turning on debugging, there is still "CPU-XBMC". Don't know, if you want to change it ... Latest build 1204 RE: OpenELEC Testbuilds for RaspberryPi Part 3 - Mydriaze - 2014-12-05 Hello everyone, I'm new to koi and i'm thinking to buy a Raspberry Pi in order to run Openelec (To be honest, i'm hesitating with a 150 euros devices such the Open Hour Chameleon). I can't find many information or video on youtube about the graphics VideoCore IV in the B+ version: Is the 25 or 50 gb Blurry running smooth on the raspberry pi and openelec? sorry if the question was answered 10 thousands times. Have a nice day. RE: OpenELEC Testbuilds for RaspberryPi Part 3 - Solo0815 - 2014-12-05 I'm trying to get my Logitech Dual Action Gamepad to work in Kodi (OE Milhouse 1204). It is recognized by OE (system), but not in Kodi: Code: OpenELECRaspi:~/.kodi/temp # lsusb Code: cat /proc/bus/input/devices It works in RetroArch out of the box btw What can I do? Thx in advance |