2014-01-24, 14:05
is there anyone here that has Windows 8 sharing folders to mygica running Linux? I would like to run Linux but cannot connect to my windows 8 shares
(2014-01-24, 14:52)superfreak79 Wrote:(2014-01-24, 14:05)Perfectdark Wrote: is there anyone here that has Windows 8 sharing folders to mygica running Linux? I would like to run Linux but cannot connect to my windows 8 shares
It works for me with Windows 8.1
(2014-01-24, 17:25)superfreak79 Wrote:(2014-01-24, 15:19)Perfectdark Wrote: are you using the Linux xbmc files linked within this thread?
Yes, the one from January 4th I think. Setup the Samba network shares via add source in Videos.
(2014-01-24, 17:42)Perfectdark Wrote:(2014-01-24, 17:25)superfreak79 Wrote:(2014-01-24, 15:19)Perfectdark Wrote: are you using the Linux xbmc files linked within this thread?
Yes, the one from January 4th I think. Setup the Samba network shares via add source in Videos.
that's what I do and when it prompts for username/password I enter it, but it still keeps prompting me
(2013-12-15, 06:59)AuXBoX Wrote: If you want to revert to Android 4.1, follow the instructions below:
1. Download update_stvmx_20130805_eng.zip and HowToRevertToBox4.1.zip
2. Unzip HowToRevertToBox4.1.zip, but not update_stvmx_20130805_eng.zip
3. Copy all files into SD/TF card root directory
factory_update_param.aml
factory_update_param.ubt
spi_MX.bin
uImage_recovery
update_stvmx_20130805_eng.zip
4. Press and hold the upgrade button, and power the device
5. Keep holding the button for about 10 seconds, and release it
6. There won’t be any display for around 2 minutes, then the upgrading screen will appear
7. The box will automatically reboot to Android upon completion
Quote:Hello
My ATV1200 was dead. Only black screen and red status light. I conected a TTL cable on serial port , on the terminal I only could see a message repeated over and over again:
EEEE I3000000032940xf3001003 03;77530EEEE I400000004294_M6_BL1_3003 >2137333EEEE I3000000032940xff00dead 16<22030EEEE I600000006294NO boot up device found 1286?1:2EEEE I500000005294enter serial boot 13549030
I wrote to geniatech and they give me this instructions and my atv is working again. I tried another bootcards before this but no one worked.
This may can help someone else:
Dear Sir
You have to make a boot card.
Please download the instruction and make a boot card as the instruction.
http://www.sendspace.com/file/kr3wta
After doing 1-4 steps of the instruction, please download the files from below link and do as readme.
http://www.sendspace.com/file/qdkl2y
Best Regards.
(2014-01-27, 12:14)Biatsch Wrote: I wrote to geniatech and they give me this instructions and my atv is working again. I tried another bootcards before this but no one worked.
This may can help someone else:
(2014-01-28, 02:57)tinker Wrote: Biatsch:
Did you actually need a serial cable to pull this off? If so, what connectors are needed at the PC and ATV ends? I've been wondering about that.
Cheers:
tinker
(2014-01-27, 12:14)Biatsch Wrote: Biatsch:
Did you actually need a serial cable to pull this off? If so, what connectors are needed at the PC and ATV ends? I've been wondering about that.
Cheers:
tinker
(2014-01-28, 06:31)AuXBoX Wrote: If you cannot boot your device into recovery mode or the led light stays red instead of going to green then you will need a serial cable.
I use usb TTL serial cable. As long as you use the sdcardmaker and the uboot_MX.bin from geniatech it will work. It took me a long time to find this out.