[fritsch]

That's "Sync playback to display" - see the first post on the settings. It's only suggested if you don't use passthrough audio. On my setup I use PCM output "Adjust Refreshrate to match video" on start / stop and additionally: Sync Playback to Display.

[gurabli]

Oki - please verify this. As drops would really suck and something is wrong.

Btw. the 4k@50 "test broadcasts" are 8 bit only? Nothing 10 bit here, yet?

Not sure about the 4k test broadcasts that Astra are currently doing - will need to take a look at this. The Astra demo videos on the demo-uhd3d.com site such as http://demo-uhd3d.com/fiche.php?cat=uhd&id=46 are 10-bit though, so they're a no-go with the Braswell of course...

EDIT: more info on Astra 4k: http://www.ses.com/ultra-hd
EDIT2: more satellite 4k channels over different satellites: http://en.kingofsat.net/ultrahd.php

I will check these 4K broadcasts too on DVB-S2. I hope they will be 8bit (slim chances). I just desperately need some time. I got the system built and also the new DVB-S2 tuner, but just don't have free time to check. (And UCL started, we will watching the MCFC-Juve last night.)

Btw, does any of you have a VDR channels.conf entry for any of the 4K test streams on one of these satellites: 13E, 19.2E, 28.2E? It would be much easier and faster to check.

[-DDD-]

Here is one 4k test channel http://channelpedia.yavdr.com/gen/DVB-S/...nnels.conf

[Engelsen]

Note: For the Jarvis version, you need to update the repository to install PVR addons, see: http://saraev.ca/oe/ (bottom notice) and install: http://saraev.ca/addons/v16/6.0/Generic/...-1.0.0.zip repository

I installed the repo but the PVR-CLient section is still empty ...

I used the new OpenElec Build ....

[fritsch]

PVR Addons have been bumped ... therefore I need to bump the OE Jarvis build and pick the new api version ...

[Engelsen]

Can u give an ETA on that? ... Sorry for being unpatient ...

[fritsch]

No - no ETA. Currently at work - you can rebase my jarvis-egl branch for me then - I can build when I get home. You can use the updated egl-isengard and upgrade later ... if that's an issue.

[Engelsen]

OK, I'll wait for that. Thx in advance ... ..

[ggp759]

That's "Sync playback to display" - see the first post on the settings. It's only suggested if you don't use passthrough audio. On my setup I use PCM output "Adjust Refreshrate to match video" on start / stop and additionally: Sync Playback to Display.

I see thanks. These 2 terms were always confusing for me. I always choose "adjust refresh rate to match video" because i want video to play at the correct playback mode with no judder. Isn't "sync playback to display" the exact opposite of that? ie play a 24p video to much the ui's 60p refresh. Also i always use passthrough. Chromebox is connected to avr.

[FernetMenta]

the point is that you can't adjust refresh rate to match video to a 100% match.

[neox387]

The isengard based builds have resolved the 1080/24p a/v sync issues for me. Thanks for the hard work!

Thanks for this feedback, though Isengard is no solution - but old code. We need to fix that in our development version. So it would be cool if you could test from time to time. Btw. does it help, if you put the following advancedsettings.xml to /storage/.kodi/userdata directory:

Code:

<advancedsettings>
<video>
  <latency>
    <delay>0</delay>
    <refresh>
      <min>23</min>
      <max>24</max>
      <delay>0</delay> <!-- set to zero or adjust if audio seems out of sync with 24p movies -->
     </refresh>
  </latency>
</video>
</advancedsettings>

^^ For OpenELEC only if you have constant out of sync issues with our Jarvis build that has moved audio syncing to AE itself and therefore is technically superior.

This fixt audio out of sync for me.
But when pausing/resuming video it's way out of sync, have to rewind/play & it's ok again

EDIT: debug of KODI http://paste.ubuntu.com/12427266/
around 16:50 - 16:52 video started from previous time all good, pause/play out of sync, rewind all good again. donno if anything is in there ..

[jjslegacy]

You know he's going to ask for a debug log right?

[BigL-New]

Kernel downloaded, installed and Bebox rebooted. I'll report any issues fund :-)

So far everything is OK, I've only 2 messages in dmesg, but they are IMHO more about general performance of the BeeBox than Kodi performance:

Code:

[ 1312.967104] perf interrupt took too long (2526 > 2500), lowering kernel.perf_event_max_sample_rate to 50000
[ 2652.076615] perf interrupt took too long (5016 > 5000), lowering kernel.perf_event_max_sample_rate to 25000

Those messages were during playback of whole 3h H.264 movie (from USB3.0 HDD connected directly).

[ggp759]

the point is that you can't adjust refresh rate to match video to a 100% match.

Ok. Saw you are saying that i should have both options enabled?

[Oshan Ruiz]

That's "Sync playback to display" - see the first post on the settings. It's only suggested if you don't use passthrough audio. On my setup I use PCM output "Adjust Refreshrate to match video" on start / stop and additionally: Sync Playback to Display.

I see thanks. These 2 terms were always confusing for me. I always choose "adjust refresh rate to match video" because i want video to play at the correct playback mode with no judder. Isn't "sync playback to display" the exact opposite of that? ie play a 24p video to much the ui's 60p refresh. Also i always use passthrough. Chromebox is connected to avr.

Confusing to me also...