Bug 5.1 Surround issue after pausing Raspberry Pi 4
#31
Update your system and try again. You should have 5.4.x kernel now.
Reply
#32
(2020-07-24, 11:57)rascas Wrote: Update your system and try again. You should have 5.4.x kernel now.

Hmmm good suggestion, but I'm now running 5.4.51-v7l+ and the problem persists  Confused
Reply
#33
Do you have a 5.1 sound system or does it happen only with 5.1 audio? If not, probably it is not the same problem.
Anyway reproduce your problem and post a Kodi debug log: https://kodi.wiki/view/Log_file
Reply
#34
(2020-07-24, 20:29)rascas Wrote: Do you have a 5.1 sound system or does it happen only with 5.1 audio? If not, probably it is not the same problem.
Anyway reproduce your problem and post a Kodi debug log: https://kodi.wiki/view/Log_file

Yes, I have a 5.1 system...I've only noticed it on 5.1 audio, but I can't confidently say it doesn't happen on others. Here's a log of it happening a few times http://paste.ubuntu.com/p/TFyDwbjgQp/ ...there's a really good example at the resume at 2020-07-25 20:30:18.261...didn't get audio for ~8 seconds after unpause
Reply
#35
(2020-07-26, 04:57)redec Wrote:
(2020-07-24, 20:29)rascas Wrote: Do you have a 5.1 sound system or does it happen only with 5.1 audio? If not, probably it is not the same problem.
Anyway reproduce your problem and post a Kodi debug log: https://kodi.wiki/view/Log_file

Yes, I have a 5.1 system...I've only noticed it on 5.1 audio, but I can't confidently say it doesn't happen on others. Here's a log of it happening a few times http://paste.ubuntu.com/p/TFyDwbjgQp/ ...there's a really good example at the resume at 2020-07-25 20:30:18.261...didn't get audio for ~8 seconds after unpause

Do you have "Keep audio device alive" and "Send low volume noise" enabled in System Settings > Audio?
I know that when pausing without these options my AVR switches to stereo mode and it takes a few seconds to go back to multichannel on resume.
I doubt this is it for you since you seem to only pause for 10s in your log though.
Reply
#36
(2020-07-27, 10:49)Axionkt Wrote:
(2020-07-26, 04:57)redec Wrote:
(2020-07-24, 20:29)rascas Wrote: Do you have a 5.1 sound system or does it happen only with 5.1 audio? If not, probably it is not the same problem.
Anyway reproduce your problem and post a Kodi debug log: https://kodi.wiki/view/Log_file

Yes, I have a 5.1 system...I've only noticed it on 5.1 audio, but I can't confidently say it doesn't happen on others. Here's a log of it happening a few times http://paste.ubuntu.com/p/TFyDwbjgQp/ ...there's a really good example at the resume at 2020-07-25 20:30:18.261...didn't get audio for ~8 seconds after unpause

Do you have "Keep audio device alive" and "Send low volume noise" enabled in System Settings > Audio?
I know that when pausing without these options my AVR switches to stereo mode and it takes a few seconds to go back to multichannel on resume.
I doubt this is it for you since you seem to only pause for 10s in your log though.
I have tried it both ways...it has no effect on my issue.

At any rate I think I'm hijacking this thread for a different issue, so I've started a new thread for my issue here
Reply
#37
(2020-06-22, 22:04)popcornmix Wrote: I have a test firmware here that may help with the mixed channel issue.
If you are affected can you test it? Use the files from the zip file to replace start.elf/fixup.dat on the boot partition of sdcard.
Let me know if it helps.

Note: On Libreelec you need to rename start4.elf to start.elf and fixup4.dat to fixup.dat (i.e. replace existing files).
Is this still applicable and is it applicable to Pi 400 or has it trickled down to a Raspbian image installed a week ago?
Reply
#38
(2020-11-24, 12:33)supsup Wrote: Is this still applicable and is it applicable to Pi 400 or has it trickled down to a Raspbian image installed a week ago?

Should be present. (needs "vcgencmd version" to report Jun 26 2020 or later).
Reply
#39
is there a list of non working rpi4 stuff for le10?
is it reasonable for LE to follow kodi release schedule now that things like h264 video accleration lack skip/jump for example?
Thanks for everyones efforts
Reply
#40
(2020-11-24, 13:01)popcornmix Wrote:
(2020-11-24, 12:33)supsup Wrote: Is this still applicable and is it applicable to Pi 400 or has it trickled down to a Raspbian image installed a week ago?

Should be present. (needs "vcgencmd version" to report Jun 26 2020 or later).
Indeed, my version is Oct 22 2020.
Reply

Logout Mark Read Team Forum Stats Members Help
5.1 Surround issue after pausing Raspberry Pi 40