Help needed no s3 in xbmcbuntu but BIOS is set for s3
#1
Hi, hopefully someone can help, I have an Asus M4a88 motherboard and have set the BIOS to S3 and installed XBMCBUNTU, however when i add the command

echo USB4 > /proc/acpi/wakeup

this is what i see


root@xbmc1:~# cat /proc/acpi/wakeup
Device S-state Status Sysfs node
PCE2 S4 *disabled pci:0000:00:02.0
PCE3 S4 *disabled
PCE6 S4 *disabled
PCE7 S4 *disabled
PCE9 S4 *disabled
PCEA S4 *disabled pci:0000:00:0a.0
RLAN S4 *enabled pci:0000:02:00.0
SBAZ S4 *disabled pci:0000:00:14.2
UAR1 S4 *disabled pnp:00:08
P0PC S4 *disabled pci:0000:00:14.4
UHC1 S4 *disabled pci:0000:00:12.0
UHC2 S4 *disabled pci:0000:00:12.1
UHC3 S4 *disabled pci:0000:00:12.2
USB4 S4 *enabled pci:0000:00:13.0
UHC5 S4 *disabled pci:0000:00:13.1
UHC6 S4 *disabled pci:0000:00:13.2
UHC7 S4 *disabled pci:0000:00:14.5
root@xbmc1:~#

please also see my lsusb and my lspci below

root@xbmc1:~# lsusb
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 002: ID 0471:060c Philips (or NXP) Consumer Infrared Transceiver (HP)
Bus 005 Device 002: ID 1ea7:0002
root@xbmc1:~#

root@xbmc1:~# lspci
00:00.0 Host bridge: Advanced Micro Devices [AMD] RS880 Host Bridge
00:02.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (ext gfx port 0)
00:0a.0 PCI bridge: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (PCIE port 5)
00:11.0 SATA controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 SATA Controller [IDE mode]
00:12.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller
00:12.1 USB Controller: ATI Technologies Inc SB7x0 USB OHCI1 Controller
00:12.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller
00:13.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller
00:13.1 USB Controller: ATI Technologies Inc SB7x0 USB OHCI1 Controller
00:13.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller
00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 3c)
00:14.1 IDE interface: ATI Technologies Inc SB7x0/SB8x0/SB9x0 IDE Controller
00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA)
00:14.3 ISA bridge: ATI Technologies Inc SB7x0/SB8x0/SB9x0 LPC host controller
00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge
00:14.5 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI2 Controller
00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor HyperTransport Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Miscellaneous Control
00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Link Control
01:00.0 VGA compatible controller: nVidia Corporation GT218 [GeForce 210] (rev a2)
01:00.1 Audio device: nVidia Corporation High Definition Audio Controller (rev a1)
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06)
root@xbmc1:~#

I have setup xbmc to suspend in settings and that work fine, however i cannot get it to wakeup, I see a red light on the MCE receiver when i press a button on the remote when the pc is supended, however it will not resume, the only way it will resume is if i press the power button on the pc case itself.

Hopefully someone can point me in the right direction.

Thanks
Reply

Logout Mark Read Team Forum Stats Members Help
Help needed no s3 in xbmcbuntu but BIOS is set for s30