2014-04-28, 21:21
Yeah - it won't get better as that :-)
50fps @ 1080p is the bare maximum an E350 can do.
50fps @ 1080p is the bare maximum an E350 can do.
(2014-04-27, 22:15)kriticar Wrote: Hi,
I have just installed xubuntu 14.04, and followed the procedure described on the first page of this thread.
...
3. in my dual monitor setup with 23" lcd monitor and 42" Panasonic plasma (reported as "Panasonic 32"" in xcfe, btw motherboard e350, RAM 4 GB ), when playing xbmc on panasonic I don't see the whole picture. If I open firefox in full screen, I cannot se the file menu (the picture starts with Edit menu), and I cannot see the title bar. The same is with the bottom of the screen as well.
On panasonic, overscan is turned off. I read in the previous posts that xrandr could be used as a solution, but I haven't tried it yet.
The same setup works with no problem with xubuntu 12.04 and glrfx drivers.
(2014-04-28, 00:20)locomot1f Wrote: @Endeavour, you are like me with the sensors.
for some reason ours is backwards -- the k10temp comes first. but the provided advancedsetting.xml is set for if the radeon-pci is first.
here's mine:
Code:<cputempcommand>sensors|sed -ne '1h;1!H;${g;s/k10temp.*temp1: \+\([-+][0-9]\+\).*/\1 C/p}'</cputempcommand>
<gputempcommand>sensors|sed -ne '1h;1!H;${g;s/k10temp.*temp1: \+\([-+][0-9]\+\).*radeon.*/\1 C/p}'</gputempcommand>
xbmc@boombox:~/testar$ sensors
radeon-pci-0008
Adapter: PCI adapter
temp1: +68.0°C (crit = +120.0°C, hyst = +90.0°C)
k10temp-pci-00c3
Adapter: PCI adapter
temp1: +67.8°C (high = +70.0°C)
(crit = +100.0°C, hyst = +97.0°C)
xbmc@boombox:~/testar$ sensors|sed -ne '1h;1!H;${g;s/k10temp.*temp1: \+\([-+][0-9]\+\).*/\1 C/p}'
radeon-pci-0008
Adapter: PCI adapter
temp1: +68.0°C (crit = +120.0°C, hyst = +90.0°C)
+67 C
xbmc@boombox:~/testar$ sensors|sed -ne '1h;1!H;${g;s/k10temp.*temp1: \+\([-+][0-9]\+\).*radeon.*/\1 C/p}'
xbmc@boombox:~/testar$
Quote: [ 4555.409817] [drm:radeon_dvi_detect] *ERROR* HDMI-A-1: probed a monitor but no|invalid EDID
(2014-04-29, 10:04)Endeavour79 Wrote:(2014-04-28, 00:20)locomot1f Wrote: @Endeavour, you are like me with the sensors.
for some reason ours is backwards -- the k10temp comes first. but the provided advancedsetting.xml is set for if the radeon-pci is first.
here's mine:
Code:<cputempcommand>sensors|sed -ne '1h;1!H;${g;s/k10temp.*temp1: \+\([-+][0-9]\+\).*/\1 C/p}'</cputempcommand>
<gputempcommand>sensors|sed -ne '1h;1!H;${g;s/k10temp.*temp1: \+\([-+][0-9]\+\).*radeon.*/\1 C/p}'</gputempcommand>
Thank you. But this doesn't work anymore;;
Output below:
Code:xbmc@boombox:~/testar$ sensors
radeon-pci-0008
Adapter: PCI adapter
temp1: +68.0°C (crit = +120.0°C, hyst = +90.0°C)
k10temp-pci-00c3
Adapter: PCI adapter
temp1: +67.8°C (high = +70.0°C)
(crit = +100.0°C, hyst = +97.0°C)
xbmc@boombox:~/testar$ sensors|sed -ne '1h;1!H;${g;s/k10temp.*temp1: \+\([-+][0-9]\+\).*/\1 C/p}'
radeon-pci-0008
Adapter: PCI adapter
temp1: +68.0°C (crit = +120.0°C, hyst = +90.0°C)
+67 C
xbmc@boombox:~/testar$ sensors|sed -ne '1h;1!H;${g;s/k10temp.*temp1: \+\([-+][0-9]\+\).*radeon.*/\1 C/p}'
xbmc@boombox:~/testar$
(2014-04-29, 13:05)fritsch Wrote: You can test my 3.14.2 kernel from some pages back.Now i am on 3.14.2-amdfixes5+ and your marantz edid. Works fine after switching resolutions in XBMC interface.
(2014-04-29, 13:35)Ectholian Wrote: I use this one on my e350:
<cputempcommand>sensors k10temp-pci-00c3 | sed -ne "s/temp1: \+[-+]\([0-9]\+\).*/\1 C/p"</cputempcommand>
<gputempcommand>sensors radeon-pci-0008 | sed -ne "s/temp1: \+[-+]\([0-9]\+\).*/\1 C/p"</gputempcommand>