•   
  • 1
  • 75
  • 76
  • 77(current)
  • 78
  • 79
  • 89
  •   
OpenELEC Testbuilds for RaspberryPi (Kodi 15.0) Part 2
(2015-06-17, 12:20)popcornmix Wrote:
(2015-06-17, 11:26)graealex Wrote: It's a shame I basically lost all working 3D options, and have to consider downgrading to Helix in order to get them back - or remove the 3D flag from the movie names so Kodi doesn't touch the movies when they are played back.

Is your TV reporting 3D support in it's edid? Can you post output of
Code:
tvservice -m CEA
or post a debug log (wiki)

I already posted it, but here it goes again:

Code:
PIWZ:~ # tvservice -m CEA
Group CEA has 17 modes:
           mode 1: 640x480 @ 60Hz 4:3, clock:25MHz progressive
           mode 2: 720x480 @ 60Hz 4:3, clock:27MHz progressive
           mode 3: 720x480 @ 60Hz 16:9, clock:27MHz progressive
  (native) mode 4: 1280x720 @ 60Hz 16:9, clock:74MHz progressive 3D:FP|TopBot
           mode 5: 1920x1080 @ 60Hz 16:9, clock:74MHz interlaced 3D:SbS-HH
           mode 6: 720x480 @ 60Hz 4:3, clock:27MHz x2 interlaced
           mode 7: 720x480 @ 60Hz 16:9, clock:27MHz x2 interlaced
  (prefer) mode 16: 1920x1080 @ 60Hz 16:9, clock:148MHz progressive
           mode 17: 720x576 @ 50Hz 4:3, clock:27MHz progressive
           mode 18: 720x576 @ 50Hz 16:9, clock:27MHz progressive
           mode 19: 1280x720 @ 50Hz 16:9, clock:74MHz progressive 3D:FP|TopBot
           mode 20: 1920x1080 @ 50Hz 16:9, clock:74MHz interlaced 3D:SbS-HH
           mode 21: 720x576 @ 50Hz 4:3, clock:27MHz x2 interlaced
           mode 22: 720x576 @ 50Hz 16:9, clock:27MHz x2 interlaced
           mode 31: 1920x1080 @ 50Hz 16:9, clock:148MHz progressive
           mode 32: 1920x1080 @ 24Hz 16:9, clock:74MHz progressive 3D:FP|TopBot
           mode 34: 1920x1080 @ 30Hz 16:9, clock:74MHz progressive

Thing is, I'd rather have the Pi not try to detect what the projector supports, because it supports TAB and SBS at all resolutions and frame rates by manually switching it to interpreting the signal as being TAB or SBS. The FP modes are sparse and only for low resolutions. With Helix this worked a treat, I could tell Kodi how to output the signal, and tell the projector to interpret it this way, and everything was fine. Now I either get a few FP modes with hdmi_force_edid_3d=1 that don't really work, especially at 24fps the DLPLink glasses wont sync, or I only get a monoscopic picture with a TAB or SBS gui.

So again, is there any way to disable any attempts of Kodi to try to match the output to the possible 3D input modes the projector supports?

BTW: Airplay support is broken now after I switched to the latest Milhouse builds. It plays one or two seconds, and then stops. The other Kodi installations, also on Raspberry Pis still work.
(2015-06-18, 22:13)graealex Wrote: BTW: Airplay support is broken now after I switched to the latest Milhouse builds. It plays one or two seconds, and then stops. The other Kodi installations, also on Raspberry Pis still work.

I'm including the latest libshairplay/AirTunes commits - requested here - which I had been told were working well.

You'll need to determine the last test build that has working Airplay (or AirTunes, whatever - I don't use Apple gear).
Texture Cache Maintenance Utility: Preload your texture cache for optimal UI performance. Remotely manage media libraries. Purge unused artwork to free up space. Find missing media. Configurable QA check to highlight metadata issues. Aid in diagnosis of library and cache related problems.
New OpenELEC Isengard build #0618: RPi / RPi2
(Supercedes previous build)

Code:
# uname -a
Linux rpi512 4.1.0-rc8 #1 Thu Jun 18 21:02:26 BST 2015 armv6l GNU/Linux

# vcgencmd version
Jun 17 2015 13:33:27
Copyright (c) 2012 Broadcom
version 1352d17ed6bd078120ac262b8c45b5b3a0d398de (clean) (release)

# lsb_release
OpenELEC (Milhouse) - Version: devel-20150618210139-#0618-gbd0c825 [Build #0618]

# vcdbg log msg 2>&1 | grep DTOK
001574.809: Kernel trailer DTOK property says yes

# Kernel device tree status: Enabled

Based on tip of OpenELEC master (bd0c8255, changelog) and tip of XBMC master (8bc1efdf, changelog) with the following modifications: Build Highlights:
  1. New kernel 4.1.0-rc8
Build Details:
  1. XBMC:
    • [videodatabase] fix invalid queries (closes #16054) (PR:7301, 1 commit, 1 file changed)
    • consider a CURLINFO_RESPONSE_CODE of zero a failed request (PR:7290, 1 commit, 1 file changed)
  2. pvr.hts:
    • Fixed: do not show HTSP version mismatch error if tvheadend server is down (PR:44, 1 commit, 3 files changed)
  3. kernel 4.1.y:
    • New commits in this build:
      • Main bcm2708/bcm2709 linux port (8e2bdce0)
      • power: Add power driver (aa090a77)
      • vc_mem: Add vc_mem driver (6290b45c)
      • Add Chris Boot's spi driver. (4d5da3fa)
      • Add Chris Boot's i2c driver (75d66251)
      • pinctrl-bcm2835: Set base to 0 give expected gpio numbering (d8f6c527)
      • platform: Add force_core command line setting to boot from a different core number (3add74da)
      • mach-bcm270x: Enable the building of pinctrl-bcm2835 (a283be0c)
      • squash: Fix inconsistency in pinctrl Makefile patch (fd08db11)
      • platform: squash: Remove IRQF_DISABLED (05376fce)
    • Commits no longer in build:
      • Main bcm2708 linux port (0e7aaf92)
      • Add 2709 platform for Raspberry Pi 2 (6763b931)
      • Add Chris Boot's i2c and spi drivers. (bb1c2fec)
      • spi-bcm2708: Prepare for Common Clock Framework migration (47303896)
      • BCM2708: Migrate to the Common Clock Framework (d8d78e0b)
      • Set a limit of 0dB on Digital Volume Control (5d1809ba)
      • BCM2708: armctrl: Add IRQ Device Tree support (15bf30de)
      • BCM2708: use pinctrl-bcm2835 (e85c6248)
      • spi: bcm2708: add device tree support (d00f2dcc)
      • i2c: bcm2708: add device tree support (13cf0c2e)
      • usb: core: make overcurrent messages more prominent (72f91c3f)
      • Revert "ARM: dma: Use dma_pfn_offset for dma address translation" (cf880d70)
      • DT: Add overrides to enable i2c0, i2c1, spi and i2s (a9a57c35)
      • lirc-rpi: Add device tree support, and a suitable overlay (4bdc71b8)
      • Fix the activity LED in DT mode (fb3c9538)
      • Adding w1-gpio device tree overlays (1c9f91aa)
      • TAS5713: return error if initialisation fails (740e2da8)
      • BCM2708_DT: Build the overlays as well (453099dc)
      • Add device tree overlay for HiFiBerry Amp/Amp+ (b39dde19)
      • Add pps-gpio DT overlay (da11da09)
      • I2C: Only register the I2C device for the current board revision (2ff35a0e)
      • BCM2708_DT: Add pcf8523-rtc overlay (32bee38e)
      • Add a parameter to turn off SPDIF output if no audio is playing (73586334)
      • bugfix for 32kHz sample rate, was missing (fdcfdf08)
      • Add device-tree overlay for ds1307 (c6e4ebd2)
      • HiFiBerry Amp: fix device-tree problems (219ae1b8)
      • BCM270x_DT: Add i2c0_baudrate and i2c1_baudrate parameters (81042a79)
      • w1-gpio: Sort out the pullup/parasitic power tangle (1184251f)
      • i2c_bcm2708: Fix clock reference counting (a0d0e3ba)
      • Add device-tree overlay for pcf2127 (dffb6179)
      • BCM2708_VCIO : Add automatic creation of device node (6547e99a)
      • Fix grabbing lock from atomic context in i2c driver (05b37ded)
      • Create bmp085_i2c-sensor-overlay.dts and update Makefile (9bdca5da)
      • serial/amba-pl011: Activate TX IRQ passively (a10a9f83)
      • serial/amba-pl011: Refactor and simplify TX FIFO handling (75d9fae6)
      • Create generic i2c-rtc overlay for supporting ds1307, ds3231, pcf2127 and pcf8523. (29cd864c)
      • dts: overlay: add support for rpi-display (600d5e0e)
      • dts: overlay: add support for HY28A display (525949ac)
      • dts: overlay: add support for HY28B display (131c6ba7)
      • dts: overlay: add support for PiScreen display (33ce6c6c)
      • dts: overlay: add support for Adafruit PiTFT (04e8bf89)
      • enable compiling spi-bcm2835 and add overlay to allow us to load the driver (917597bf)
      • dts: overlay: add support for MZ61581 display (58f834d5)
      • dts: overlay: piscreen: set speed to 24MHz (080c66df)
      • dts: overlay: rpi-display: pullup irq gpio (c34aef08)
      • BCM270x_DT: add bcm2835-dma entry (7268b2f1)
      • bcm270x: add mmc-bcm2835 clock (ccc2b25a)
      • BCM270x_DT: add bcm2835-mmc entry (7520bcef)
      • BCM270x_DT: Refactor bcm2708.dtsi and bcm2709.dtsi (7504524f)
      • bcm2708: fix uart1 parameters (196c354f)
      • spi: bcm2835: fix all checkpath --strict messages (8243fc28)
      • spi: bcm2835: fill/drain SPI-fifo as much as possible during interrupt (54e38f32)
      • spi: bcm2835: clock divider can be a multiple of 2 (52469b2a)
      • spi: bcm2835: enable support of 3-wire mode (b3622510)
      • spi: bcm2835: move to the transfer_one driver model (c71501bc)
      • spi: bcm2835: fix code formatting issue (cf51ed16)
      • spi: bcm2835: fill FIFO before enabling interrupts to reduce interrupts/message (8f0e96a7)
      • spi: bcm2835: transform native-cs to gpio-cs on first spi_setup (31a827cc)
      • spi: bcm2835: enabling polling mode for transfers shorter than 30us (776aadc5)
      • spi: bcm2835: change timeout of polling driver to 1s (0a92a307)
      • HiFiBerry Digi: set SPDIF status bits for sample rate (d8512fe4)
      • bcm2708-dmaengine: Add debug options (496a822b)
      • BCM270x: Add memory and irq resources to dmaengine device and DT (4504d174)
      • dmaengine: bcm2708: Merge with arch dma.c driver and disable dma.c (4111e2c0)
      • BCM270x: dma: Remove driver (2b9f3386)
      • BCM270x: Remove dmaman device (d2647dd9)
      • mmc: bcm2835-mmc: Make available on ARCH_BCM2835 (40cd8a80)
      • bcm2835: bcm2835_defconfig enable MMC_BCM2835 (6c0c2255)
      • bcm2835: Change to use bcm2835-mmc in Device Tree (8bff84b0)
      • dmaengine: increment privatecnt when using dma_get_any_slave_channel (89df9a42)
      • bcm2835-mmc: Add locks when accessing sdhost registers (0ecdaeb7)
      • bcm2835-mmc: Add range of debug options for slowing things down (d7580af2)
      • BCM270x: Correct vcio device memory resource and add irq resource (e3457809)
      • video: fbdev: bcm2708_fb: Don't panic on error (4b03fd42)
      • BCM2708: vcio: Fix checkpatch issues (1965f1d8)
      • BCM2708: vcio: Remove unused code and compact comments (f7567a97)
      • BCM2708: vcio: Move character device teardown to driver remove (406f0f62)
      • BCM2708: vcio: Restructure error paths (fa189cd5)
      • BCM2708: vcio: Move some macros from header to driver (ce2c991a)
      • BCM2708: vcio: Only store the register base address (71c6a727)
      • BCM2708: vcio: Do not print messages in module init (30e7622c)
      • BCM2708: vcio: Use device resources (7a912897)
      • BCM270x: power: Change initcall level to subsys (1e5c7135)
      • BCM270x: Use bcm2708-vcio (41e80f86)
      • BCM270x: Remove arch driver vcio.c (5bb0a0c8)
      • bcm2835: bcm2835_defconfig enable BCM2708_MBOX (8cb40db6)
      • bcm2835: Add mailbox bcm2708-vcio to Device Tree (c03f517d)
      • mailbox: bcm2708-vcio: Allocation does not need to be atomic (2010049a)
      • mailbox: bcm2708-vcio: Check the correct status register before writing (f8655981)
      • bcm2835-sdhost: Error handling fix, and code clarification (7a6f0938)
      • bcm2835-sdhost: Adding overclocking option (d5025127)
      • bcm2835-mmc: Adding overclocking option (ae7169ee)
      • dmaengine: bcm2708: set residue_granularity field (4b4b9568)
      • BCM2708_DT: Adding starter Compute Module DTS files (1ddcc631)
      • bcm2835-sdhost: Round up the overclock, so 62 works for 62.5Mhz (210157c8)
      • bcm2835-mmc: Round up the overclock, so 62 works for 62.5Mhz (a946e70f)
      • BCM2708_DT: Add missing CM aliases (f80dd318)
      • usb: dwc_otg: Don't use dma_to_virt() (90c3a2ff)
      • fixup: restore dma-mapping.h (785584ea)
      • fbdev: bcm2708_fb: Add ARCH_BCM2835 support (1b1de682)
      • BCM270x: Remove header file mach/dma.h (e6d3d3d4)
      • BCM270x_DT: Add bcm2708-fb device (11e90851)
      • ARM: bcm2835: Use 0x4 prefix for DMA bus addresses to SDRAM. (0abe9b6f)
      • bcm2835: Add bcm2708-fb to Device Tree (fabd2cdb)
      • bcm2835: bcm2835_defconfig use FB_BCM2708 (81530cfc)
      • BCM2708_DT: Enable mmc and fb in the CM dtsi (9e0da80c)
      • BCM270x: Add vchiq device to platform file and Device Tree (c95de8db)
      • bcm2708: vchiq: Add Device Tree support (b723b439)
      • bcm2835: Add bcm2835-vchiq to Device Tree (a368d938)
      • i2c-bcm2708: When using DT, leave the GPIO setup to pinctrl (0bf6760b)
      • vchiq: Change logging level for inbound data (aa0aca81)
      • BCM270x: Add onboard sound device to Device Tree (32477cf5)
      • bcm2835: Add bcm2835-audio to Device Tree (a8d9f167)
      • config: Add CONFIG_CIFS_UPCALL (ead779a2)
      • config: Add CONFIG_FB_SSD1307=m (2728618d)
      • vcsm: Add ioctl for custom cache flushing (ee5567b6)
      • dts: overlay: add generic support for ads7846 (6f9e2f73)
      • bcm270x: add dtparam for audio node (beda21eb)
      • device-tree: spi: make spi-bcm2835 the default spi driver and prepare for dma (9f10489e)
      • BCM270x: Move power module (8c5dd3fb)
      • bcm2835: Use empty bootargs in Device Tree (7ea54e25)
      • scripts/mkknlimg: Add support for ARCH_BCM2835 (2ab7f22f)
      • config: add KEYBOARD_GPIO (73bb23f8)
      • dts: overlay: add support for tinylcd.com 3.5" display (d7d34720)
      • BCM270X_DT: Move the overlays into a subdirectory, adding the README (4b843d5b)
      • Swap X Y axis of ads7846 touchscreen controller for PiScreen TFT (9c292092)
      • Added optional parameter to set resistance of touch plate(x-plate-ohms) (a4d11970)
      • BCM270x: Move vc_mem (df11ad94)
      • BCM270x: Add USB controller to Device Tree (7495f032)
      • added mcp251x module to list of modules to get compiled as well as the corresponding overlay (da534564)
      • BCM270x: Move thermal sensor to Device Tree (8e999dc4)
      • bcm2835: Add thermal sensor to Device Tree (fd724791)
      • BCM270x: Enable bcm2835_wdt and bcm2835-rng (34638ffe)
      • BCM270X_DT: Add bcm2835-pm-wdt and bcm2835-rng (6779bd79)
      • bcm2835: Match BCM270X Device Trees (e98419e0)
      • dts: Enable overlays on ARCH_BCM2835 (3ac358b4)
      • bcm2835: Make camera and sound drivers available (6c632134)
      • bcm2835: Merge bcm2835_defconfig with bcmrpi_defconfig (b5b5fa6e)
      • BCM270x_DT: Configure UART using DT (c712b42d)
      • vchiq_arm: ARCH_BCM2835 compatibility (aa05d1fe)
      • BCM270x_DT: Enable UART in the example Compute Module DTS as well (fa0a4bff)
      • bcm270x defconfigs: Remove spurious entries (fae583ca)
      • BCM270x_DT: Add a label to the clocks node, and a few aliases (549ff9d4)
      • sdhost-overlay: Move clock declaration out of /soc (1b8bcc8e)
      • BCM270X_DT: Enable 'make clean' on overlays directory (24d8164a)
      • hwmon: Remove bcm2835-hwmon (2b53c727)
      • BCM270x: Make uart1 work with Device Tree (a4573f4e)
      • fixup: BCM2709: Remove unused clock implementation (31c0f40b)
      • BCM270x: Remove bcm2708_systemtimer and bcm2708_powerman (6ae9c7a9)
      • dwc_otg: Fix crash when fiq_enable=0 (1659f9a7)
      • BCM270x_DT: Add interrupt pin to enc28j60-overlay (6a0071a9)
      • BCM270x_DT: Delete deprecated RTC overlays (ccba72f3)
      • BCM270x_DT: Update overlays/README (815f7d17)
      • bcm2708-i2s: Enable MMAP support via a DT property and overlay (0b667dd3)
      • BCM270x_DT: Correcting URL in README (dc48d12d)
      • dts/overlays: Add DHT11 overlay (bd75bda9)
      • configs: add IIO and DHT11 support to bcm2709/bcmrpi_defconfig (b9a67332)
      • Merge pull request #1017 from P33M/rpi-4.0.y (5cc39075)
      • squash: Add some missing depends to Kconfig files (520cdbce)
      • BCM270x_DT: Default Compute Module i2c, i2s and spi support (077e7ea6)
  4. Additional commits/pull requests/changes not yet merged upstream:
    • Added: patch: Update to kernel 4.1-rc8
    • Added: patch: Configure kernel 4.1-rc8
Texture Cache Maintenance Utility: Preload your texture cache for optimal UI performance. Remotely manage media libraries. Purge unused artwork to free up space. Find missing media. Configurable QA check to highlight metadata issues. Aid in diagnosis of library and cache related problems.
Hi,
with build 0618 is not possible to enable pvr.hts
0617 shows mismatch error, go to settings disable and enable tv, after that it works
The next build will include PR7305, which presumably fixes that issue with pvr.hts.
Texture Cache Maintenance Utility: Preload your texture cache for optimal UI performance. Remotely manage media libraries. Purge unused artwork to free up space. Find missing media. Configurable QA check to highlight metadata issues. Aid in diagnosis of library and cache related problems.
ok, thanks
Hey,

since Build #0618 my Hifiberry Digi is no longer working (i'm not able to choose it as my audio output device).

dmesg shows this:
snd-hifiberry-digi: sound: ASoC: CPU DAI (null) not registered
snd-hifiberry-digi: sound: snd_soc_register_card() failed: -517
snd-hifiberry-digi: sound: ASoC: CODEC DAI wm8804-spdif not registered
snd-hifiberry-digi: sound: snd_soc_register_card() failed: -517

After i downgrade to #0617 everything is working again (thy Pi detects the Digi and i can choose it as my audio output device).

How can i help to track down the problem?
I'll see if I can fix that (Wolfson) in tonight's build - the wm8804 options aren't enabled in the new kernel.

Edit: I added WM8804 SPI and I2C as modules (these options are both new to 4.1) but I'm still seeing the same errors as you, so the dtb and/or driver may require a tweak - I've pinged @popcornmix. Hopefully this is an easy fix and doesn't have to go back to Hifiberry to make their driver compatible with the 4.1 kernel.
Texture Cache Maintenance Utility: Preload your texture cache for optimal UI performance. Remotely manage media libraries. Purge unused artwork to free up space. Find missing media. Configurable QA check to highlight metadata issues. Aid in diagnosis of library and cache related problems.
(2015-06-19, 16:44)Milhouse Wrote: I'll see if I can fix that (Wolfson) in tonight's build - the wm8804 options aren't enabled in the new kernel.

Edit: I added WM8804 SPI and I2C as modules (these options are both new to 4.1) but I'm still seeing the same errors as you, so the dtb and/or driver may require a tweak - I've pinged @popcornmix. Hopefully this is an easy fix and doesn't have to go back to Hifiberry to make their driver compatible with the 4.1 kernel.

Please don't stress yourself, I can remain at #0617.
But thanks for your fast response.
New OpenELEC Isengard build #0619: RPi / RPi2
(Supercedes previous build)

Code:
# uname -a
Linux rpi512 4.1.0-rc8 #1 Fri Jun 19 21:02:31 BST 2015 armv6l GNU/Linux

# vcgencmd version
Jun 17 2015 13:33:27
Copyright (c) 2012 Broadcom
version 1352d17ed6bd078120ac262b8c45b5b3a0d398de (clean) (release)

# lsb_release
OpenELEC (Milhouse) - Version: devel-20150619210144-#0619-g6ff0766 [Build #0619]

# vcdbg log msg 2>&1 | grep DTOK
001574.533: Kernel trailer DTOK property says yes

# Kernel device tree status: Enabled

Based on tip of OpenELEC master (6ff0766c, changelog) and tip of XBMC master (1d20e723, changelog) with the following modifications: Build Highlights:
  1. No fix yet for Hifiberry-Digi - investigations ongoing
  2. Bump pvr.hts, although I suspect this won't fix the issue reported by @chipi. Continued problems may need to be reported in the pvr.hts support thread.
  3. Updated sdhost driver:
    popcornmix Wrote:Phil's pushed an sdhost update that fixes an issue with a Lexar card.

    If overclocking, it also will wind down the sdcard overclock on errors. As data transfers are protected with a CRC, this is safe-ish,
    so in theory you can specify a too-high overclock and it will settle back to a reliable overclock.

    Of course there are no guarantees with this, so backup before experimenting, but it should make sdcard overclock a little safer.
Build Details:
  1. OpenELEC:
    • kodi: remove unused splash images (5b166e0a)
    • installer: fix menu display, log file function (1ebb205d)
    • projects/RPi*: switch to kernel 4.1, update RPi support patches (9e5a6172)
    • linux: remove linux-4.0 support (6ff0766c)
  2. XBMC:
    • [pvr] bump pvr.hts to 2.1.11 (PR:7305, 1 commit, 1 file changed)
    • [win32][curl] Using CEnvironment::unsetenv() instead of SetEnvironmen… (PR:7307, 1 commit, 1 file changed)
  3. pvr.hts:
    • Fixed channel icon compatibility issue with recent tvheadend servers. (PR:47, 1 commit, 3 files changed)
  4. kernel 4.1.y:
    • New commits in this build:
      • BCM270X_DT: Document the i2s-mmap overlay (1c4271ab)
      • bcm2835-sdhost: Improve error handling and recovery (13b3cb93)
  5. Additional commits/pull requests/changes not yet merged upstream:
    • Added: patch: Enable Wolfson 8804 SPI/I2C modules
Texture Cache Maintenance Utility: Preload your texture cache for optimal UI performance. Remotely manage media libraries. Purge unused artwork to free up space. Find missing media. Configurable QA check to highlight metadata issues. Aid in diagnosis of library and cache related problems.
Hi,

I'm having a hard time watching simple Half-SBS Videos with the new build. It only displays one side of it on the whole screen now. When Support MVC and Full HD 3d Option are disabled, it seems to only display one half in 2D, although it renders the interface in 3d. When it's enabled, it seems to try to create a 3D FP output, but that doesn't really work, the projector recognizes a FP signal, but it's not 3D. It's just... blurred.

The file is named ...3D.SBS.... and works flawlessly with kodi 14

Real MVC MKVs work fine btw, but only if I rename them to ...3D.SBS..., they don't work with ...3D.MVC... or ...3D.FP...

Thanks for help
(2015-06-20, 10:32)Catscrash Wrote: The file is named ...3D.SBS.... and works flawlessly with kodi 14

What is the last test build (prior to #0619) where this works for you? Also a debug log (wiki) from #0619 would be useful.
Texture Cache Maintenance Utility: Preload your texture cache for optimal UI performance. Remotely manage media libraries. Purge unused artwork to free up space. Find missing media. Configurable QA check to highlight metadata issues. Aid in diagnosis of library and cache related problems.
(2015-06-20, 02:25)Milhouse Wrote:
  • No fix yet for Hifiberry-Digi - investigations ongoing

I'm using a Hifiberry-Digi+ w/ transformer on my Pi2, and it works with optical and SPDIF output, including AC3 and DTS passthrough. Maybe I can help?

(2015-06-20, 10:32)Catscrash Wrote: Hi,

I'm having a hard time watching simple Half-SBS Videos with the new build. It only displays one side of it on the whole screen now. When Support MVC and Full HD 3d Option are disabled, it seems to only display one half in 2D, although it renders the interface in 3d. When it's enabled, it seems to try to create a 3D FP output, but that doesn't really work, the projector recognizes a FP signal, but it's not 3D. It's just... blurred.

The file is named ...3D.SBS.... and works flawlessly with kodi 14

That's the same problem I'm experiencing. SBS or TAB MKV Videos are marked 3D.XXX and were interpreted correctly on Helix 14.2, with the GUI and the video switching into SBS or TAB, now with Kodi 15 it always tries to put out some form of FP stream, even when no suitable 3D-FP mode is reported by the output device, like in my case. This usually leads to a monoscopic view of the video, while the GUI actually switches to TAB or SBS, depending on the selection and settings.

@Milhouse: any way to have an option to disable 3D-FP output alltogether for devices that don't play along well, so it reverts back to the "old" behavior of just outputting SBS or TAB without any frame packing? I think this problem will only ever get really resolved for output devices that support the full range of 3D resolutions and frame rates, like brand new 3D TVs and the like. My projector isn't just capable of receiving a full 1080p/60Hz FP video stream, only:
  • 1280x720 @ 60Hz 16:9, clock:74MHz progressive 3D:FP|TopBot
  • 1280x720 @ 50Hz 16:9, clock:74MHz progressive 3D:FP|TopBot
  • 1920x1080 @ 24Hz 16:9, clock:74MHz progressive 3D:FP|TopBot

@Catscrash:

You might want to turn on hdmi_force_edid_3d=1 in config.txt. That solved the problem at least half way, but only for FP supported resolutions.

(2015-06-18, 22:39)Milhouse Wrote: I'm including the latest libshairplay/AirTunes commits - requested here - which I had been told were working well.

You'll need to determine the last test build that has working Airplay (or AirTunes, whatever - I don't use Apple gear).

Thanks, I'll update and see how it works. I also don't use Apple gear, but a Synology NAS with DS Audio, and AirPlay allows for simultaneous streaming to multiple devices, while DLNA/UPnP only allows control of one device at a time. The gaps between songs are also smaller. With DLNA, it always takes a few seconds after the song ends and the next one starts.

I mean, in my wishlist I also have gapless or even crossfaded playback with either DLNA or AirPlay, but that's probably not possible with a non-Apple AirPlay source and non-Apple Airplay player devices, as the current song and the next one would have to be streamed at the same time, which requires support from all devices and software involved.
(2015-06-20, 02:25)Milhouse Wrote: [*]Updated sdhost driver:
popcornmix Wrote:Phil's pushed an sdhost update that fixes an issue with a Lexar card.

If overclocking, it also will wind down the sdcard overclock on errors. As data transfers are protected with a CRC, this is safe-ish,
so in theory you can specify a too-high overclock and it will settle back to a reliable overclock.

Of course there are no guarantees with this, so backup before experimenting, but it should make sdcard overclock a little safer.

With this my Raspberry (OC 1000/500 and SDRAM to 480) hangs on different stages. Sometimes the booting needs "ages", sometimes after starting a movie the complete RPI hangs
(2015-06-20, 15:05)querty1000 Wrote: With this my Raspberry (OC 1000/500 and SDRAM to 480) hangs on different stages. Sometimes the booting needs "ages", sometimes after starting a movie the complete RPI hangs

And the same configuration with #0618 works without a problem? What about #0619 but without overclocks, is that any better? Anything in the #0619 dmesg? What type of SD card (brand, model, size/capacity etc.)? Are you overclocking sdhost?
Texture Cache Maintenance Utility: Preload your texture cache for optimal UI performance. Remotely manage media libraries. Purge unused artwork to free up space. Find missing media. Configurable QA check to highlight metadata issues. Aid in diagnosis of library and cache related problems.
  •   
  • 1
  • 75
  • 76
  • 77(current)
  • 78
  • 79
  • 89
  •   



Logout Mark Read Team Forum Stats Members Help
OpenELEC Testbuilds for RaspberryPi (Kodi 15.0) Part 214
This forum uses Lukasz Tkacz MyBB addons.