2016-05-07, 12:30
0505 worked without any problems for me.
(2016-05-07, 10:35)opeters Wrote:(2016-05-07, 04:24)KILLERNADS Wrote: Okay finally managed to update my windows 7 HTPC (with Kodi 14.1) to Windows 10, just so that i could install this WIP build and try to play some 3D bluray ISO files.
Unfortunately, i had no such luck
I installed the latest build from the 1st page, i think it was version 17.0, however this build gave me a lot of issues.
Firstly, i could not even access my Videos section in the Settings screen, even some other tabs like Appearance was not doing anything, i.e. clicking on the headings did not load up any panel on the right.
I followed the instructions on the ...
Not sure, but are you using another language than English ?
If you do and upgrade you don't see any text. So before upgrading set the gui to English and change it after upgrade. Also it is better to do a clean install.
I also recommend to create a win 10 boot image from your upgraded system and do a clean install of win 10. This saves a lot of disk space and performance.
(2016-05-07, 04:24)KILLERNADS Wrote: Okay finally managed to update my windows 7 HTPC (with Kodi 14.1) to Windows 10, just so that i could install this WIP build and try to play some 3D bluray ISO files.
Unfortunately, i had no such luck
I installed the latest build from the 1st page, i think it was version 17.0, however this build gave me a lot of issues.
Firstly, i could not even access my Videos section in the Settings screen, even some other tabs like Appearance was not doing anything, i.e. clicking on the headings did not load up any panel on the right.
I followed the instructions on the screenshots, but could not get very far as i couldn't change most of the settings within Kodi Video settings All the intel settings i changed perfectly fine!
This is my primary HTPC in which i use Kodi everyday, hence i quickly installed the latest Kodi Jarvis build over the top from the Kodi website. Thankfully, i got access to all my settings again!
I also tried playing some blurays, surprising i could now load up 2d ISO and blurays just fine, don't think i could do that previously.
However, i then tried to load up a 3d bluray iso file, to my surprise it did load up fine but played the film in 2D mode, i don't think it even gave me a 3d option!?
(2016-05-07, 14:00)KILLERNADS Wrote:(2016-05-07, 10:35)opeters Wrote:(2016-05-07, 04:24)KILLERNADS Wrote: Okay finally managed to update my windows 7 HTPC (with Kodi 14.1) to Windows 10, just so that i could install this WIP build and try to play some 3D bluray ISO files.
Unfortunately, i had no such luck
I installed the latest build from the 1st page, i think it was version 17.0, however this build gave me a lot of issues.
Firstly, i could not even access my Videos section in the Settings screen, even some other tabs like Appearance was not doing anything, i.e. clicking on the headings did not load up any panel on the right.
I followed the instructions on the ...
Not sure, but are you using another language than English ?
If you do and upgrade you don't see any text. So before upgrading set the gui to English and change it after upgrade. Also it is better to do a clean install.
I also recommend to create a win 10 boot image from your upgraded system and do a clean install of win 10. This saves a lot of disk space and performance.
Hi,
No im already using English! Its just the top few tabs in settings that didnt click through such as appearance and video. The bottom ones seemed to work fine. Also in using aeon nox skin from my previous install.
I would really like to get it working without spending time going through a fresh install. Although for now anyway i have switched to release 16, where everything works well just without 3d bluray support i assume.
(2016-05-07, 16:32)KILLERNADS Wrote: One other thing that i forgot to add. Yesterday when i followed the settings on the main page, i changed the following one:
Adjust display refresh rate = start / stop
However this gave me issues, i was watching revenant last night and the audio was not in sync, the voices were not in lip sync withe video, when I switched this back tk off then eveything was working better again!
(2016-05-07, 16:28)KILLERNADS Wrote: Oh right, damn yeah i think i realised it was a skin issue when i woke up this korning and hit me as to why i didnt try another skin out last night ?
A shame that Aeon Nox is not supported yet as thats the skin ive only used for the past 6 years in kodi/xbmc ?
Ive customised it too much also with my own headings and sections, it would be way to much work and time consuming to do the same thing for another skin.
Well i will go ahead and install wip krypton anyway and check if it works first or not. Then decide from there, hopefully i can still switch back to aeon nox after changing the settings in the default skin. I understand that aeon nox maybe broken in krypton but i think it was only the settings part that was giving me issues, everything else seemed to work fine.
(2016-05-07, 18:18)hdmkv Wrote: I'm now ATMOS/X capable; woohoo! ! ... @movie78, you mentioned needing to use the latest beta driver for just the audio (especially ATMOS/X) with D34010WYK NUC. Just confirming if it was this one? Does NOT show i3-4010U (or Intel HD Graphics 4400) as one of the "valid" products it's meant for. Did you read somewhere that it was okay to use w/D34010WYK?It's mention in the release notes, only use the Audio drivers from Beta drivers.
(2016-05-07, 18:18)hdmkv Wrote: I'm now ATMOS/X capable; woohoo! !