2016-06-28, 12:10
Hello,
I bought a TechnoTrend TT-budget CT2-4500 [1,2] DVB-C card.
By recommendation from the list linux-media I use the older firmware from http://palosaari.fi/linux/v4l-dvb/firmwa...40/4.0.11/
According to linuxtv.org my card is an OEM version of the DVB Sky T980C).
The TV part is working, however the IR receiver is not working yet.
I do a modprobe ir-kbd-i2c, the journal then says:
The device works as a dev/input device:
However, I can get no results from event17 using `cat /dev/input/event17`.
The remote works (I can see the IR blinking using a cellphone camera)
Also, lircd gets no results:
Now using irw /var/run/lirc/lircd also get's no signales from the remote.
Any hints you might have? Any more lowlevel debugging ideas?
Thanks,
Florian
[1] http://www.technotrend.eu/2984/TT-budget...00_CI.html
[2] https://www.linuxtv.org/wiki/index.php/T...T2-4500_CI
[3] https://github.com/OpenELEC/dvb-firmware...r/firmware
[4] https://aur.archlinux.org/packages/opene...-firmware/
[5] https://www.linuxtv.org/wiki/index.php/DVBSky_T980C
I bought a TechnoTrend TT-budget CT2-4500 [1,2] DVB-C card.
By recommendation from the list linux-media I use the older firmware from http://palosaari.fi/linux/v4l-dvb/firmwa...40/4.0.11/
According to linuxtv.org my card is an OEM version of the DVB Sky T980C).
The TV part is working, however the IR receiver is not working yet.
I do a modprobe ir-kbd-i2c, the journal then says:
Code:
kernel: Registered IR keymap rc-fusionhdtv-mce
kernel: input: i2c IR (FusionHDTV) as /devices/virtual/rc/rc0/input20
kernel: rc rc0: i2c IR (FusionHDTV) as /devices/virtual/rc/rc0
kernel: ir-kbd-i2c: i2c IR (FusionHDTV) detected at i2c-7/7-006b/ir0 [cx23885[0]]
The device works as a dev/input device:
Code:
# ir-keytable
Found /sys/class/rc/rc0/ (/dev/input/event17) with:
Driver ir-kbd-i2c, table rc-fusionhdtv-mce
Supported protocols: unknown
Enabled protocols: unknown
Name: i2c IR (FusionHDTV)
bus: 24, vendor/product: 0000:0000, version: 0x0000
Repeat delay = 500 ms, repeat period = 125 ms
However, I can get no results from event17 using `cat /dev/input/event17`.
The remote works (I can see the IR blinking using a cellphone camera)
Also, lircd gets no results:
Code:
# lircd --loglevel=debug --nodaemon -H dev/input -d /dev/input/event17
lircd-0.9.3a[2273]: Warning: Running as root
lircd-0.9.3a[2273]: Info: Using remote: Technotrend.
lircd-0.9.3a[2273]: Notice: lircd(devinput) ready, using /var/run/lirc/lircd
Now using irw /var/run/lirc/lircd also get's no signales from the remote.
Any hints you might have? Any more lowlevel debugging ideas?
Thanks,
Florian
[1] http://www.technotrend.eu/2984/TT-budget...00_CI.html
[2] https://www.linuxtv.org/wiki/index.php/T...T2-4500_CI
[3] https://github.com/OpenELEC/dvb-firmware...r/firmware
[4] https://aur.archlinux.org/packages/opene...-firmware/
[5] https://www.linuxtv.org/wiki/index.php/DVBSky_T980C