[blank]

I hope it is OK that I ask here.

I have 2 lightpacks that I wan't to get working with boblight

I haven't installed any libraries for the prismatik,
meaning only boblight/d is installed, and the according libraries.

this is my config

Code:

[global]

[device]
name            LP1
channels        30
type            lightpack
interval        20000
#bus            2
#address        4
serial          95230303231351C020B1

[device]
name            LP2
channels        30
type            lightpack
interval        20000
#bus            2
#address        5
serial          95230303231351E0F1C1


[color]
name            red
rgb             FF0000
gamma           1.6
adjust          1.0
blacklevel      0.0

[color]
name            grn
rgb             0000FF
gamma           1.6
adjust          1.0
blacklevel      0.0

[color]
name            blu
rgb             00FF00
gamma           1.6
adjust          1.0
blacklevel      0.0

[light]
name            L01
color           red     LP1 1
color           blu     LP1 2
color           grn     LP1 3
hscan           83 100
vscan           75 100

[light]
name            L02
color           red     LP1 4
color           blu     LP1 5
color           grn     LP1 6
hscan           83 100
vscan           75 100

[light]
name            L03
color           red     LP1 7
color           blu     LP1 8
color           grn     LP1 9
hscan           83 100
vscan           50 75

[light]
name            L04
color           red     LP1 10
color           blu     LP1 11
color           grn     LP1 12
hscan           67 83
vscan           75 100

[light]
name            L05
color           red     LP1 13
color           blu     LP1 14
color           grn     LP1 15
hscan           50 67
vscan           75 100

[light]
name            L06
color           red     LP1 16
color           blu     LP1 17
color           grn     LP1 18
hscan           83 100
vscan           25 50

[light]
name            L07
color           red     LP1 19
color           blu     LP1 20
color           grn     LP1 21
hscan           83 100
vscan           0 25

[light]
name            L08
color           red     LP1 22
color           blu     LP1 23
color           grn     LP1 24
hscan           83 100
vscan           0 25

[light]
name            L09
color           red     LP1 25
color           blu     LP1 26
color           grn     LP1 27
hscan           67 83
vscan           0 25

[light]
name            L10
color           red     LP1 28
color           blu     LP1 29
color           grn     LP1 30
hscan           50 67
vscan           0 25

[light]
name            L11
color           red     LP2 1
color           blu     LP2 2
color           grn     LP2 3
hscan           50 67
vscan           0 25

I have only inserted 1 LED strip for LP2 (I am adding 1 by 1)

but, when I start boblightd, LP2 is not showing anything, and looking at the debug, it is like it is adding and throwing the connection for both LP1 and LP2 again and again (I only took a snippet of the log..)

Code:

(CDeviceLightpack::SetupDevice) LP2: found Lightpack at bus 2 address 4, serial is 95230303231351E0F1C1
(CDevice::Process)              LP2: setup succeeded
(CDevice::Process)              LP1: closed
(CDevice::Process)              LP1: setting up
(CDeviceLightpack::SetupDevice) LP1: found Lightpack at bus 2 address 3, serial is 95230303231351C020B1
(CDeviceLightpack::SetupDevice) LP1: Lightpack is initialized, bus 2 device address 3
(CDeviceLightpack::SetupDevice) LP1: found Lightpack at bus 2 address 4, serial is 95230303231351E0F1C1
(CDevice::Process)              LP1: setup succeeded
(CDevice::Process)              LP2: closed
(CDevice::Process)              LP2: setting up
(CDeviceLightpack::SetupDevice) LP2: found Lightpack at bus 2 address 3, serial is 95230303231351C020B1
(CDeviceLightpack::SetupDevice) LP2: Lightpack is initialized, bus 2 device address 3
(CDeviceLightpack::SetupDevice) LP2: found Lightpack at bus 2 address 4, serial is 95230303231351E0F1C1
(CDevice::Process)              LP2: setup succeeded
(CClientsHandler::ParseSet)     127.0.0.1:42039 priority set to 255
(CDevice::Process)              LP1: closed
(CDevice::Process)              LP1: setting up
(CDeviceLightpack::SetupDevice) LP1: found Lightpack at bus 2 address 3, serial is 95230303231351C020B1
(CDeviceLightpack::SetupDevice) LP1: Lightpack is initialized, bus 2 device address 3
(CDeviceLightpack::SetupDevice) LP1: found Lightpack at bus 2 address 4, serial is 95230303231351E0F1C1
(CDevice::Process)              LP1: setup succeeded
(CDevice::Process)              LP2: closed
(CDevice::Process)              LP2: setting up
(CDeviceLightpack::SetupDevice) LP2: found Lightpack at bus 2 address 3, serial is 95230303231351C020B1
(CDeviceLightpack::SetupDevice) LP2: Lightpack is initialized, bus 2 device address 3
(CDeviceLightpack::SetupDevice) LP2: found Lightpack at bus 2 address 4, serial is 95230303231351E0F1C1
(CDevice::Process)              LP2: setup succeeded
^C(SignalHandler)                 caught SIGINT
(CClientsHandler::GetReadableFd)select() Interrupted system call
(main)                          signaling devices to stop
(CClientsHandler::Cleanup)      disconnecting clients
(CClientsHandler::RemoveClient) removing 127.0.0.1:42039
(CClientsHandler::Cleanup)      closing listening socket
(CClientsHandler::Cleanup)      clients handler stopped
(main)                          waiting for devices to stop
(CDevice::Process)              LP2: closed
(CDevice::Process)              LP2: stopped
(CDevice::Process)              LP1: closed
(CDevice::Process)              LP1: stopped
(main)                          exiting

Well, I can get LP1 working, so I am thinking that it is OK, that I haven't installed prismatik, or any libraries.
I have used the prismatik, and both lightpacks are working, I just didn't like how prismatik worked.

Have anyone experienced anything like this in their quest of using boblight with lightpack..? thanks