2009-11-15, 01:15
I've been reading every thread on here about resume and remotes, and have tried everything listed so far, but am unable to get resume to work, so looking for some help.
I've tried doing the
Ive tried doing the Echo USB0 > /proc/acpi/wakeup thing for every usb device listed by lsusb, and this is what I see in my terminal:
Here is the last portion of my xbmc.log file
http://pastebin.com/m4c52d7aa
here is my rc.local file:
http://pastebin.com/m53059ff8
Here is my menu.lst file:
http://pastebin.com/m4e4ca459
Here is my lircmap.xml file
http://pastebin.com/m302a5806
Here is my hardware.conf file
http://pastebin.com/m5a905dcd
And finally, my lircd.conf file:
http://pastebin.com/m3defefb1
my specs are in my system, I have the newer zotac board that supports STR, I have S3 enabled in my bios, I have resume from everything turned on, and can't seem to figure this out. If I hit a button on the keyboard, it will resume, but remote does not. I', using a Harmony 550 remote, with a HA-IR01SV IR receiver From here
There is one thing i noticed, however, but dont know if its the problem. If i do LSUSB, I see this:
however even though I did Echo USB4 (for Bus 4) it still doesn't show a USB4 in the cat above...could this be it?
Thanks
Update: I've made a small amount of progress. REading a post here, I added a new device to my remote, called "windows media center" and left the defaults. Now if i use that device, I can get it to resume by hitting the "PwrToggle" button on the remote, however once resumed, power toggle does not send it back to sleep...I have to switch back to the Harmony PVR to get it to go back to sleep, but at least it looks like resuming sorta works...now how do i get it to work on the harmony device settings?
I've tried doing the
Quote:kernel /boot/vmlinuz-<version> root=UUID=<some-uuid> ro quiet splash usbcore.autosuspend=-1thing.
Ive tried doing the Echo USB0 > /proc/acpi/wakeup thing for every usb device listed by lsusb, and this is what I see in my terminal:
Quote:(T: XBMCLive)root@XBMCLive:~# cat /proc/acpi/wakeupI can get the system to suspend to ram via the power button from within XBMC, but cannot get it to resume.
Device S-state Status Sysfs node
PS2K S4 disabled pnp:00:08
SMB0 S4 disabled pci:0000:00:03.2
USB0 S4 enabled pci:0000:00:04.0
USB2 S4 enabled pci:0000:00:04.1
US15 S4 disabled pci:0000:00:06.0
US12 S4 disabled pci:0000:00:06.1
NMAC S5 disabled pci:0000:00:0a.0
PBB0 S4 disabled pci:0000:00:09.0
HDAC S4 disabled pci:0000:00:08.0
XVR0 S4 disabled pci:0000:00:0c.0
XVR1 S4 disabled
P0P5 S4 disabled
P0P6 S4 disabled pci:0000:00:15.0
P0P7 S4 disabled pci:0000:00:16.0
P0P8 S4 disabled pci:0000:00:17.0
P0P9 S4 disabled pci:0000:00:18.0
PWRB S4 *enabled
Here is the last portion of my xbmc.log file
http://pastebin.com/m4c52d7aa
here is my rc.local file:
http://pastebin.com/m53059ff8
Here is my menu.lst file:
http://pastebin.com/m4e4ca459
Here is my lircmap.xml file
http://pastebin.com/m302a5806
Here is my hardware.conf file
http://pastebin.com/m5a905dcd
And finally, my lircd.conf file:
http://pastebin.com/m3defefb1
my specs are in my system, I have the newer zotac board that supports STR, I have S3 enabled in my bios, I have resume from everything turned on, and can't seem to figure this out. If I hit a button on the keyboard, it will resume, but remote does not. I', using a Harmony 550 remote, with a HA-IR01SV IR receiver From here
There is one thing i noticed, however, but dont know if its the problem. If i do LSUSB, I see this:
Quote:(T: XBMCLive)root@XBMCLive:~# lsusb
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 002: ID 1784:0008 TopSeed Technology Corp.
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
however even though I did Echo USB4 (for Bus 4) it still doesn't show a USB4 in the cat above...could this be it?
Thanks
Update: I've made a small amount of progress. REading a post here, I added a new device to my remote, called "windows media center" and left the defaults. Now if i use that device, I can get it to resume by hitting the "PwrToggle" button on the remote, however once resumed, power toggle does not send it back to sleep...I have to switch back to the Harmony PVR to get it to go back to sleep, but at least it looks like resuming sorta works...now how do i get it to work on the harmony device settings?