2010-09-24, 19:15
So it's official then: I am an idiot... could have sworn I checked out r157.....
But dude, seriously, I could kiss you!
Jim
But dude, seriously, I could kiss you!
Jim
jelleeelco Wrote:Now I've been reading this thread from start to finish, got most of it up-and-running thanks to the great tutorials / advice on this platform...thanks to all.
BUT..(there is always a 'but' after a compliment ) I can't get one thing sorted out. Updating ATVClient so that I can use my harmony one...
I think I would be helped a lot if someone could confirm WERE on PIN87s image the ATVClient is installed. I tried to follow the instructions of installing ATVclient under ubuntu, I think it all worked but then FTP into the ATV didn't allow me to create atvclient.xml (in order to options=-m ).
Thanks in advance,
Jelle
xbmc@AppleTV:~$ whereis atvclient
atvclient: /usr/local/sbin/atvclient
Sam.Nazarko Wrote:Update the driver. The BCM70015 was not in G/A stage when the images were constructed
Philmatic Wrote:On pin87's image:
Code:xbmc@AppleTV:~$ whereis atvclient
atvclient: /usr/local/sbin/atvclient
fauxfive55 Wrote:Can I copy the new driver file(s) onto the usb stick with the restored image or do I have a build a new image with the driver preinstalled?
What's the easiest way to go about this?
Thanks again!
curlyjs Wrote:Great news...
May I suggest a few points that would be nice improvements...
- Navigation sounds
http://forum.xbmc.org/showpost.php?p=598...tcount=965
- Have parted installed to partition AppleTV HD or a new HD
http://forum.xbmc.org/showpost.php?p=604...count=1021
- Maybe a script to partition and copy.
Philmatic Wrote:http://forum.xbmc.org/showpost.php?p=571...tcount=668
If you enter in all of those commands, you'll have the latest version of XBMC and the latest firmware/library/drivers for the CrystalHD card. I have a 70015 and r157 works for me.
mkdir chd
cd chd
svn checkout http://crystalhd-for-osx.googlecode.com/svn/trunk crystalhd-r156
cd crystalhd-r156/crystalhd/linux_lib/libcrystalhd
make
sudo make install
cd ../../driver/linux
autoconf
./configure
make
sudo make install
sudo modprobe crystalhd
cd \
rm -rf chd
[ 52.572497] Loading crystalhd v3.5.0
[ 53.004658] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input5
[ 53.032477] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 53.343445] nvidia: module license 'NVIDIA' taints kernel.
[ 53.392687] udev: renamed network interface eth0 to eth1
[ 54.595305] crystalhd 0000:02:00.0: Starting Device:0x1615
[ 54.595343] PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
[ 54.595354] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 54.595363] crystalhd 0000:02:00.0: bar0:0x22800000-0x00010000 bar2:0x22000000-0x00800000
[ 54.595417] crystalhd 0000:02:00.0: i2o_addr:0xd1260000 Mapped addr:0xd1f80000
[ 54.702482] PCI: Setting latency timer of device 0000:02:00.0 to 64
[ 54.702696] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 54.702709] PCI: Setting latency timer of device 0000:01:00.0 to 64
[ 54.702877] NVRM: loading NVIDIA UNIX x86 Kernel Module 100.14.19 Wed Sep 12 14:12:24 PDT 2007
[ 55.972600] loop: module loaded
[ 56.054632] lp: driver loaded but no devices found
[ 56.518111] Adding 499992k swap on /dev/sdb4. Priority:-1 extents:1 across:499992k
[ 56.845928] EXT3 FS on sdb3, internal journal
[ 57.713383] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 59.478216] NET: Registered protocol family 17
[ 60.863961] No dock devices found.
[ 63.102387] NET: Registered protocol family 10
[ 63.103021] lo: Disabled Privacy Extensions
[ 106.025403] Marking TSC unstable due to: cpufreq changes.
[ 106.032016] Time: hpet clocksource has been installed.
[ 106.536160] Clocksource tsc unstable (delta = -100075419 ns)
[ 66.275542] eth1: link up, 100Mbps, full-duplex, lpa 0x45E1
[ 75.649721] crystalhd 0000:02:00.0: Entering chd_dec_open
[ 75.649730] crystalhd 0000:02:00.0: Opening new user[0] handle
[ 94.968212] [crystalhd_flea_download_fw]: Sz:864276
[ 95.080625] crystalhd 0000:02:00.0: [crystalhd_flea_download_fw]: step 7. Done RetVal:400019
[ 77.118275] eth1: no IPv6 routers present
goldfinger7476 Wrote:I have been trying to look around but can't find a clear answer, is there a performance benefit from installing pins image to the harddrive rather than running it off the flash drive? or is it completely cached there already upon boot?
davidflam Wrote:Solved it... =)
Same problem as xeonicxpression, adjust tv refresh rate is messing things up. Take a look a his post http://forum.xbmc.org/showpost.php?p=609...count=1068.
Thanks!