[seribralcrow]

Every forum I have found only has guides for the 0038 and ffdc receivers. I have tried to adapt them to work with my version with no success. Does anyone have this type of receiver? I have tried it with and without lirc using ir-keytables. ir-keytables recognizes my receiver but the test doesn't display anything. I have tried running Ubuntu 11.10 and 12.04. Currently I have 12.04 installed on my machine.

cat /proc/bus/input/device:

I: Bus=0003 Vendor=15c2 Product=0043 Version=0002
N: Name="iMON Remote (15c2:0043)"
P: Phys=usb-0000:00:06.0-1/input0
S: Sysfs=/devices/pci0000:00/0000:00:06.0/usb4/4-1/4-1:1.0/rc/rc0/input12
U: Uniq=
H: Handlers=kbd event12
B: PROP=0
B: EV=100013
B: KEY=fff 0 4400000108c0320 2d5008000000000 30000 400119000 418614000801 809e168000000000 200000010004002
B: MSC=10

sudo ir-keytables:

Found /sys/class/rc/rc0/ (/dev/input/event12) with:
Driver imon, table rc-imon-pad
Supported protocols: RC-6 other
Enabled protocols:
Repeat delay = 500 ms, repeat period = 125 ms

I would really appreciate it if anyone could help. This setup has been quite frustrating for me.

[ikus060]

May you give us the output of lsmod ?
Your remote should work out of the box with default linux kernel and this without lirc. Check if you have the following module : rc_core, rc_imon_pad, imon.

[seribralcrow]

Here is the information you requested. The modules you listed are indeed started but I am not able to make the remote work. Is there any special configuration that I must do?

lsmod:
Module Size Used by
hid_logitech 26520 0
vesafb 13844 1
snd_hda_codec_hdmi 32474 1
snd_hda_codec_realtek 223867 1
parport_pc 32866 0
ppdev 17113 0
joydev 17693 0
rfcomm 47604 12
mxm_wmi 12979 0
bnep 18281 2
snd_hda_intel 33773 3
snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel
snd_hwdep 13668 1 snd_hda_codec
snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec
snd_seq_midi 13324 0
psmouse 87603 0
snd_rawmidi 30748 1 snd_seq_midi
ir_lirc_codec 12859 0
lirc_dev 19204 1 ir_lirc_codec
ir_mce_kbd_decoder 12777 0
ir_sony_decoder 12510 0
ir_jvc_decoder 12507 0
ir_rc6_decoder 12507 0
rc_imon_pad 12505 0
ir_rc5_decoder 12507 0
nvidia 12319264 40
ir_nec_decoder 12507 0
xpad 18179 0
imon 32839 0
ff_memless 13097 2 hid_logitech,xpad
video 19596 0
shpchp 37277 0
rc_core 26412 10 ir_lirc_codec,ir_mce_kbd_decoder,ir_sony_decoder,ir_jvc_decoder,ir_rc6_decoder,rc_imon_pad,ir_rc5_decoder,ir_nec_decoder,imon
serio_raw 13211 0
snd_seq_midi_event 14899 1 snd_seq_midi
wmi 19256 1 mxm_wmi
snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event
snd_timer 29990 2 snd_pcm,snd_seq
snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq
snd 78855 16 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
btusb 18288 2
mac_hid 13253 0
bluetooth 180104 23 rfcomm,bnep,btusb
soundcore 15091 1 snd
snd_page_alloc 18529 2 snd_hda_intel,snd_pcm
i2c_nforce2 13058 0
lp 17799 0
parport 46562 3 parport_pc,ppdev,lp
usbhid 47199 1 hid_logitech
hid 99559 2 hid_logitech,usbhid
forcedeth 63460 0

[boosted]

Have you seen this
http://forum.xbmc.org/showthread.php?s=a...tid=104541

[seribralcrow]

I looked over this thread and it would not work for me. To ensure that the receiver functioned properly I verifed its functionality on a windows install. The receiver and remote work exceptionally well in windows. When I ran dmesg it seems to configure properly. However, I get no IR input signals when I run ir-keytables. To ensure this was not something that I had done wrong, I am using a fresh install of 12.04 with ir-keytable installed only. I am doing this to eliminate the possibility of conflicts. The author states that if you are receiving no input then the driver is not configured or installed properly. How can I verify/correct this?

[skerit]

I'm running into the same problem. Something's not right on ubuntu 12.04. I also tried the old lirc approach (without devinput), but even then it won't budge.

[seribralcrow]

With help from Sparkie2640

Try:

Code:

ir-keytable -c
ir-keytable -w /lib/udev/rc_keymaps/imon_mce
ir-keytable -t

Hitting a few buttons made my remote respond.

[HackitZ]

Thanks for the tip it worked perfectly,

does anyone know how to get the lcd working?