Posts: 382
Joined: Aug 2009
Reputation:
3
Hi, i will watch it tomorow and post new version in the morning...
Posts: 382
Joined: Aug 2009
Reputation:
3
I see for the "bug", you should not have the rights to the directory c:\program file\xbne\dll, check ...
Posts: 77
Joined: Apr 2010
Reputation:
0
Bonjour Vincent,
Thank you for the message. Frankly speaking, I do not quite understand your phrase: "you should not have the rights to the directory c:\program file\xbne\dll, check ..."
First of all, I do not know anything about the rights to the above directory. What should I check? What else should I do?
Thanks, Alex
Posts: 382
Joined: Aug 2009
Reputation:
3
Hello,
Trying to make a copy of the file "c:\Program Files\xbne\DLL\SQLite4WD.dll" and call it "c:\Program Files\xbne\DLL\SQLite4WD_2.dll".
you should have two files: "SQLite4WD.dll" and "SQLite4WD_2.dll" in directory DLL of xbne.
Posts: 77
Joined: Apr 2010
Reputation:
0
Hi Vincent,
I followed your instruction and made a copy of the subject file, renamed it and put it in the same folder where the original file is.
Tried to start the application. The result is the same as before - does not work. The error message is attached.
Thanks, Alex
Erreur à la ligne 42 du traitement Méthode mySQLExec.
Vous avez appelé la fonction AppelDLL32.
Erreur au chargement de la DLL 'SQLite4WD3_2.dll'
Détail de l'erreur système :
The specified module could not be found.
(126)
----- Informations techniques -----
Projet : nfo_xbm
Appel WL :
Traitement de 'Méthode mySQLExec' (c_SQLite4WD.mySQLExec), ligne 42, thread 0
Fonction 'AppelDLL32', syntaxe 0
Que s'est-il passé ?
Erreur au chargement de la DLL 'SQLite4WD3_2.dll'
Code erreur : 2802
Niveau : erreur fatale (EL_FATAL)
Code d'erreur système : 126
Message d'erreur système :
The specified module could not be found.
Dump de l'erreur du module 'WD150VM.DLL' (15.00Jz).
Identifiant des informations détaillées (.err) : 2802
Informations de débogage :
Fonction (0,18)
Informations supplémentaires :
EIT_PILEWL :
Méthode mySQLExec (c_SQLite4WD.mySQLExec), ligne 42
Procédure globale SQL_mySQLExec_Plus (Procedures globales de nfo_xbm.SQL_mySQLExec_Plus), ligne 6
Procédure locale Synchro_MiseAJour_Id (FenetrePrincipale.PROCEDURE.Synchro_MiseAJour_Id), ligne 31
Procédure locale Charge_Base (FenetrePrincipale.PROCEDURE.Charge_Base), ligne 442
Initialisation de FenetrePrincipale (FenetrePrincipale), ligne 139
EIT_DATEHEURE : 05/08/2010 18:25:13
Assistance
Posts: 382
Joined: Aug 2009
Reputation:
3
Hello,
Oups, I was wrong, it SQLite4WD3.dll need to copy and rename SQLite4WD3_2.dll.
And download the last version 9.3.4.2.
Posts: 77
Joined: Apr 2010
Reputation:
0
2010-08-08, 17:41
(This post was last modified: 2010-08-08, 20:31 by albaranov.)
Bonjour Vincent,
1. I have downloaded the new version of XBNE, and now it works. Thanks a lot!
2. The file SQLite4WD3_2.dll was already there, so no need to copy and rename.
3. Synchronization between two XBMC installed on different computers. I followed all steps described by you earlier. When I clicked on "Valid" button an error message appeared again and synchronization was not complete.
Any ideas, please?
Can you please advise if I can copy the required files manually from the main PC to the living room PC? If yes, what are these files and the address to where they should be copied?
Alex
Erreur à la ligne 3 du traitement Méthode mySQLConnecte.
Les dimensions d'un tableau doivent être positives.
----- Informations techniques -----
Projet : nfo_xbm
Appel WL :
Traitement de 'Méthode mySQLConnecte' (c_SQLite4WD.mySQLConnecte), ligne 3, thread 0
Que s'est-il passé ?
Les dimensions d'un tableau doivent être positives.
Code erreur : 2329
Niveau : erreur fatale (EL_FATAL)
Dump de l'erreur du module 'WD150VM.DLL' (15.00Jz).
Identifiant des informations détaillées (.err) : 2329
Informations supplémentaires :
EIT_PILEWL :
Méthode mySQLConnecte (c_SQLite4WD.mySQLConnecte), ligne 3
Procédure locale Synchro_Init_Base (FenetrePrincipale.PROCEDURE.Synchro_Init_Base), ligne 45
Clic sur BTN_Valid (Fen_Reseau.BTN_Valid), ligne 36
EIT_DATEHEURE : 08/08/2010 11:34:27
Assistance
Posts: 77
Joined: Apr 2010
Reputation:
0
Hi XBNE experts,
It looks like the developer is not available. I have an inquiry regarding XBNE, and hope that somebody has already come across the answer to my question.
My NFO files are located together with the video files in the same folder. The have the same name, e.g. "First Blood.avi" and "First Blood.nfo". Some NFO files do not have "year" of the movie. When I use XBNE Editor I see that the "year" field is blank. So I update this field and save changes. Now the XBNE reflects the year for this movie. However the respective NFO file stays intact- "year" field is still blank.
Is it normal? If yes, what does the XBNE Editor edit? I thought it was the NFO file. If it is abnormal what should I do differently? I'm concerned that if I do something wrong all the long hours that I have spent on updating/correcting movie details could be wasted.
Thank you,
Alex
Posts: 16
Joined: Apr 2009
Reputation:
0
Hi,
where I can manage the trailers?
Thanks.
Picard
Posts: 77
Joined: Apr 2010
Reputation:
0
2010-08-12, 15:04
(This post was last modified: 2010-08-12, 16:32 by albaranov.)
Hi Vincent, just confirming that it was and is checked. Thanks, Alex
Posts: 382
Joined: Aug 2009
Reputation:
3
Hi,
I just tested at home, and the year is correctly recorded in the nfo.
Verifies that XBNE has access to movies, otherwise it saves the nfo in the folder c:\program file\xbne\nfo.