2011-01-17, 10:01
with my 00015 r174 worked like a charm (unlike the r156), but I upgraded in the same step to a xbmc svn (yesterday), maybe it was a combination.
interceptor121 Wrote:That's weird as 156 does not have the 0015 support that is what r174 is for?
andrewspearns Wrote:@bestyman, are you using a Mac or a PC?
xeonicxpression Wrote:I assume you are talking about installing it on the appletv. All you have to do is SSH into the Appletv and then do that command on the first post that starts with defaults. Then it will be in the Downloads section of Launcher, the same place you installed xbmc from. If you are on Windows, use PuTTY to ssh in. Just type in the IP of your appletv and make sure connection type is set to ssh. Can't get much easier than that!
feikenberg Wrote:Did you enable ssh when using the patchstick creator? i think it is not enabled by default.
Quote:bash-2.05b# dmesg | grep -i crystal
BroadcomCrystalHD: Found HW and started driver SW.
crystalhd_hw_open: setting up functions, device = Flea
[crystalhd_flea_core_reset]: Starting core reset
BroadcomCrystalHD opened
[crystalhd_flea_download_fw]: Sz:864276
[crystalhd_flea_download_fw]: step 1. Enable scrubbing
[crystalhd_flea_download_fw]: step 2. Poll for SCRAM_KEY_DONE_INT
[crystalhd_flea_download_fw]: step 3. Write the BORCH and STARCH addresses. f6004:d2fff, f6008:d2fff
[crystalhd_flea_download_fw]: step 4. Write the firmware to DRAM. Sz:864256 Bytes
[crystalhd_flea_download_fw]: step 5. Write the signature to CMAC register.
[crystalhd_flea_download_fw]: step 6. Write the ARM run bit to 1.
[crystalhd_flea_download_fw]: step 7. Poll for Boot Verification done/failure interrupt.
[crystalhd_flea_download_fw]: step 7. Done RetVal:400018
[crystalhd_flea_download_fw]: Complete.
crystalhd_flea_do_fw_cmd entered
[crystalhd_flea_core_reset]: Starting core reset
BroadcomCrystalHD closed
crystalhd_hw_open: setting up functions, device = Flea
[crystalhd_flea_core_reset]: Starting core reset
BroadcomCrystalHD opened
[crystalhd_flea_download_fw]: Sz:864276
[crystalhd_flea_download_fw]: step 1. Enable scrubbing
[crystalhd_flea_download_fw]: step 2. Poll for SCRAM_KEY_DONE_INT
[crystalhd_flea_download_fw]: step 3. Write the BORCH and STARCH addresses. f6004:d2fff, f6008:d2fff
[crystalhd_flea_download_fw]: step 4. Write the firmware to DRAM. Sz:864256 Bytes
[crystalhd_flea_download_fw]: step 5. Write the signature to CMAC register.
[crystalhd_flea_download_fw]: step 6. Write the ARM run bit to 1.
[crystalhd_flea_download_fw]: step 7. Poll for Boot Verification done/failure interrupt.
[crystalhd_flea_download_fw]: step 7. Done RetVal:400019
[crystalhd_flea_download_fw]: Complete.
crystalhd_flea_do_fw_cmd entered
[crystalhd_flea_core_reset]: Starting core reset
BroadcomCrystalHD closed
crystalhd_hw_open: setting up functions, device = Flea
[crystalhd_flea_core_reset]: Starting core reset
BroadcomCrystalHD opened
[crystalhd_flea_download_fw]: Sz:864276
[crystalhd_flea_download_fw]: step 1. Enable scrubbing
[crystalhd_flea_download_fw]: step 2. Poll for SCRAM_KEY_DONE_INT
[crystalhd_flea_download_fw]: step 3. Write the BORCH and STARCH addresses. f6004:d2fff, f6008:d2fff
[crystalhd_flea_download_fw]: step 4. Write the firmware to DRAM. Sz:864256 Bytes
[crystalhd_flea_download_fw]: step 5. Write the signature to CMAC register.
[crystalhd_flea_download_fw]: step 6. Write the ARM run bit to 1.
[crystalhd_flea_download_fw]: step 7. Poll for Boot Verification done/failure interrupt.
[crystalhd_flea_download_fw]: step 7. Done RetVal:400018
[crystalhd_flea_download_fw]: Complete.
crystalhd_flea_do_fw_cmd entered
crystalhd_flea_do_fw_cmd entered
crystalhd_flea_do_fw_cmd entered
crystalhd_flea_do_fw_cmd entered
crystalhd_flea_do_fw_cmd entered
crystalhd_flea_do_fw_cmd entered
crystalhd_flea_do_fw_cmd entered
[crystalhd_flea_core_reset]: Starting core reset
BroadcomCrystalHD closed
bash-2.05b#
Quote:bash-2.05b# kextstat | grep crystalhd
65 0 0x2b858000 0x11000 0x10000 com.broadcom.crystalhd.driver (3.8.1) <5 4 3 2>
andy204 Wrote:This is the easiest way to install the CrystalHD driver onto your AppleTV!I am moving from XBMC on Xbox (died recently) to AppleTV and am stuck on install the CrystalHD drivers for bcm70015. I used ATV-USB Creator and installed XBMC without any problems and the bcm70015 is installed, but I do not have an option in downloads for the CrystalHD drivers even after adding
To make this easy install available log into your AppleTV
Code:
and enter:
Code:defaults write com.teamxbmc.xbmclauncher XBMCAdditionalDownloadPlistURLs -array-add http://crystalhd.sartori.at/files/crystalhd.plist
This will add a new download source to your "Downloads" section in Launcher.
--