2010-05-04, 22:13
A friend of mine asked me if it was possible, as far as I know it isn't. I have a Acer 3610 with XBMC live installed.
mobious Wrote:A friend of mine asked me if it was possible, as far as I know it isn't. I have a Acer 3610 with XBMC live installed.
mobious Wrote:Oh my god I am so sorry guys I completely forgot about this topic. Thank you so much for your replies. What Gabbott said, how is it possible? like turn it on from cold? or if its set to sleep? If its from cold could someone elaborate on what I should get please?
mobious Wrote:A friend of mine asked me if it was possible, as far as I know it isn't. I have a Acer 3610 with XBMC live installed.
mobious Wrote:Thanks for the replies guys, yeah I assumed the IR remote woulnd't turn it on unless it was on sleep. So WOL, my question is, is the only possible way to do that through my PC? as if I have to turn on my pc to turn on my revo, I might aswell just turn on the revo amirite?
There are a few WOL apps for the iPhone, was wondering if anyone here tried em out?
Quote:xbmc@xbmc-desktop:~$ ifconfig
eth0 Link encap:Ethernet HWaddr 90:fb:a6:2c:b2:1f
inet addr:192.168.1.11 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::92fb:a6ff:fe2c:b21f/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:3432 errors:0 dropped:0 overruns:0 frame:0
TX packets:3621 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1096890 (1.0 MB) TX bytes:762787 (762.7 KB)
Interrupt:23 Base address:0xe000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:512 errors:0 dropped:0 overruns:0 frame:0
TX packets:512 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:33814 (33.8 KB) TX bytes:33814 (33.8 KB)
wlan0 Link encap:Ethernet HWaddr 90:4c:e5:4e:0d:cb
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
wmaster0 Link encap:UNSPEC HWaddr 90-4C-E5-4E-0D-CB-00-00-00-00-00-00-00-00-00-00
UP RUNNING MTU:0 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
#!/bin/bash
ethtool -s eth0 wol g
exit
/etc/init.d/wakeonlanconfig
ethtool -s eth0 wol g
ethtool -s wmaster0 wol g
Quote:root@xbmc-desktop:/etc/init.d# /etc/init.d/wakeonlanconfig
Cannot get current wake-on-lan settings: Operation not supported
not setting wol
jhsrennie Wrote:I'm a little baffled by your post. As far as I know WOL is purely a hardware system and you shouldn't need any fiddling with the OS. You just enable it in the BIOS, and the only other thing you need is the target MAC address. Assuming you're connected through the ethernet cable (not the wireless) the MAC address you need is 90:fb:a6:2c:b2:1f.