[Trexx]

I am getting an issue with the following config:

AppleTV w/Broadcom 70015 card
XBMC Build: sshc nightly - r34416
Crystal 3.8.0 drivers (downloaded zip from google page)

Dmesg after boot, but before running XBMC:
http://pastebin.com/0DsyWBCg

Dmesg right after launching XBMC (but before box locked up):
http://pastebin.com/39jp4PRq

Corresponding XBMC Log
http://pastebin.com/KGmy02kg

Issue also occurred on XBMC nightlies (svr r33778 - Dharma beta2)

[davilla]

"!!FATAL ERROR!! Core Reset Failure"

that's not good. If you revert to 3.6.0 ?

[Trexx]

"!!FATAL ERROR!! Core Reset Failure"

that's not good. If you revert to 3.6.0 ?

3.6.0 Works fine.

From 3.6.0:

BroadcomCrystalHD: Found HW and started driver SW.
Opening new user[0] handle
crystalhd_hw_open: setting up functions, device = Flea
DDR-2 Detected
Opening HW. hw:0x2320604, hw->adp:0x1e91b00
BroadcomCrystalHD opened
allocated 18 elem
Initializing Dio pool 10 1024 305c 0x1e156a4
[crystalhd_flea_download_fw]: Sz:864276
[crystalhd_flea_download_fw]: step 1. Enable scrubbing
[crystalhd_flea_download_fw]: step 2. Poll for SCRAM_KEY_DONE_INT
[crystalhd_flea_download_fw]: step 3. Write the BORCH and STARCH addresses. f6004:d2fff, f6008:d2fff
[crystalhd_flea_download_fw]: step 4. Write the firmware to DRAM. Sz:864256 Bytes
[crystalhd_flea_download_fw]: step 5. Write the signature to CMAC register.
[crystalhd_flea_download_fw]: step 6. Write the ARM run bit to 1.
[crystalhd_flea_download_fw]: step 7. Poll for Boot Verification done/failure interrupt.
[crystalhd_flea_download_fw]: step 7. Done RetVal:400019
[crystalhd_flea_download_fw]: ..... Complete.
crystalhd_flea_do_fw_cmd entered
Closing user[0] handle
Releasing RX Pkt pool
Released dio pool 10
no element found
released 18 elem
BroadcomCrystalHD closed

[davilla]

GRRRRRRRR. Pulling that 3.8.0 until I can see what's going on.

[Trexx]

GRRRRRRRR. Pulling that 3.8.0 until I can see what's going on.

I also ran into same issue when I compiled the r161 code myself, but wasn't sure if I had just screwed up something on the compile or not.

[davilla]

Lovely, I'm not seeing any problems under OSX and bcm70015 with 3.8.0.

[Trexx]

Lovely, I'm not seeing any problems under OSX and bcm70015 with 3.8.0.

My AppleTV was built with atv-usbcreator. Has Software Menu, NitoTV, Launcher, etc. installed.

I did upgrade to the 10.4.9 update via NitoTv. It also has hooked up a USB Hub, Keyboard, & ext. HD.

I don't know if any of those could potentially cause a problem.

The CrystalHD is being loaded via script, not via rc.local. Not sure if that would make any difference or not either.

[beytarj]

moved

[Trexx]

Lovely, I'm not seeing any problems under OSX and bcm70015 with 3.8.0.

Any luck on finding the root cause on this Davilla?

[davilla]

Any luck on finding the root cause on this Davilla?

Can't reproduce and I'm not seeing any other reports from users doing self builds.

[Trexx]

Can't reproduce and I'm not seeing any other reports from users doing self builds.

The issue was found using both a self build and using the precanned binaries that you had briefly posted.

If there are some debug settings that would give you more data, or a debug version of the drivers, I am more than happy to try those to help isolate the root cause.

[Patrics83]

Almost the same issue here. Installed the drivers with andy204´s script (r172)

DMESG, before launching xbmc and after launching xbmc: http://pastebin.ca/1973176

XBMC LOG: http://pastebin.ca/1973183

Hope it helps.

[davilla]

The issue was found using both a self build and using the precanned binaries that you had briefly posted.

If there are some debug settings that would give you more data, or a debug version of the drivers, I am more than happy to try those to help isolate the root cause.

r172 is current svn rev at crystalhd-for-osx.

[Patrics83]

Did the info i posted you help?

[davilla]

Did the info i posted you help?

"Firmware command T/O" looks suspiciously like what happens when an old layout bcm70012 is clocked to 200MHz rather than 180MHz.